Industrial

This document describes wiring terminals, main circuit terminal connections and main circuit terminal wiring specifications for the standard E7 drive. The contents of this document are included in the E7 User Manual TM.E7.01.

The LTC2436-1 is a 2-channel differential input micropower 16-bit No Latency ∆Σ analog-to-digital converter with an integrated oscillator. It provides 0.5LSB INL and 800nV RMS noise independent of VREF. The two differential channels convert alternately with a channel identification included in the conversion result. It uses delta-sigma technology and provides single conversion settling of the digital filter. Through a single pin, the LTC2436-1 can be configured for better than 87dB input differential mode rejection at 50Hz and 60Hz ±2%, or it can be driven by an external oscillator for a user defined rejection frequency. The internal oscillator requires no external frequency setting components. The converter accepts any external differential reference voltage from 0.1V to VCC for flexible ratiometric and remote sensing measurement configurations. The full-scale differential input range is from –0.5•VREF to 0.5•VREF. The reference common mode voltage, VREFCM, and the input common mode voltage, VINCM, may be independently set anywhere between GND and VCC. The DC common mode input rejection is better than 140dB. The LTC2436-1 communicates through a flexible 3-wire digital interface which is compatible with SPI and MICROWIRE protocols.

The LTM4605 is a high efficiency switching mode buck-boost power supply from Philips. It operates over an input voltage range of 4.5V to 20V and supports an output voltage range of 0.8V to 16V. The maximum output current is 5A. This product uses a single inductor architecture, and the input voltage can be higher, lower, or equal to the output voltage. The LTM4605 uses a high switching frequency and current mode architecture, which provides a very fast transient response to line and load changes. The product also has overvoltage and foldback current protection. The LTM4605 is available in a small, thermally enhanced 15mm x 15mm x 2.8mm LGA package and is RoHS compliant.

The IR3842WMPbF is an easy-to-use, fully integrated and highly efficient DC/DC synchronous Buck regulator. It features an integrated MOSFETs and on-chip PWM controller, making it a space-efficient solution for low output voltage applications. It also offers programmability of start up time, switching frequency and current limit while operating in wide input and output voltage range. The switching frequency is programmable from 250kHz to 1.5MHz for an optimum solution. It also features important protection features such as over current protection, PGood output, hiccup current limit and precision reference voltage.

The CS5516 and CS5520 are complete solutions for digitizing low-level signals from strain gauges, load cells, and pressure transducers. These devices offer an on-chip software programmable instrumentation amplifier block, choice of DC or AC bridge excitation, and software selectable reference and signal demodulation. The CS5516 uses delta-sigma modulation to achieve 16-bit resolution at output word rates up to 60 Hz. The CS5520 achieves 20-bit resolution at word rates up to 60 Hz. The CS5516 and CS5520 sample at a rate set by the user in the form of either an external CMOS clock or a crystal. On-chip digital filtering provides rejection of all frequencies.

LM3543 Triple Port USB Power Distribution Switch and Over-Current Protection

The PS8821-1, -2 are optically coupled isolators containing a GaAlAs LED on the light emitting diode (input side) and a PIN photodiode and a high-speed amplifier transistor on the output side on one chip. The PS8821-2 is suitable for high density applications. It features 40% reduction of mounting area (5-pin SOP × 2), low power consumption (VCC = 3.3 V), high isolation voltage (BV = 2 500 Vr.m.s.), high-speed response (tPHL = 0.6 μs MAX., tPLH = 0.9 μs MAX.), and Pb-Free product. It is approved by UL (File No. E72422) and DIN EN60747-5-2 (VDE0884 Part2).

This document introduces the features and characteristics of Vishay Semiconductors VLMG31 series SMD LED products, including high brightness, compatibility with automatic placement equipment, RoHS compliance, compatibility with multiple soldering processes, and low power consumption.

The data sheet introduces the features and characteristics of LTC1876 high performance triple output switching regulator and step-up regulator. The chip uses dual phase, dual synchronous step-down switching controller, drives all N-channel synchronous power MOSFET stages, and an internal 1A, 36V step-up regulator provides the third output. The chip uses OPTI-LOOP compensation, which optimizes the transient response over a wide range of output capacitance and ESR values. Each controller's RUN/SS pin provides both soft-start and an optional timed, short-circuit shutdown function that can be configured to latch off one or both controllers. Current foldback provides additional short-circuit protection. In an overvoltage condition, the bottom MOSFET is latched on until VOUT returns to normal. The FCB pin can be used to inhibit Burst Mode operation or to enable regulation of a secondary output voltage. The step-up regulator operates at 1.2MHz, allowing the use of tiny low cost capacitors and inductors. In addition, its internal 1A switch allows high current outputs to be generated. Its current mode control scheme provides excellent line and load regulation.

Legris, a member of Group Legris Industries, designs, manufactures and markets innovative solutions for connecting, conveying and controlling industrial fluids. They offer a wide range of products and services to meet the requirements of various sectors. Legris adopts an ongoing strategy of research and product innovation to provide new solutions and wider applications to its customers. With a worldwide presence, Legris is able to better understand the changes and specific requirements of each market in order to offer the best solutions.

The LTC1261 is a voltage inverter that can provide a regulated negative voltage from a single positive supply. It features adjustable or fixed output voltages, low output ripple, shutdown mode, and guaranteed output regulation.

The AD8387 is a 12-bit, 12-channel, high-performance LCD DecDriver that provides high accuracy and high resolution video output.

The ACS755xCB-100 is a Hall current sensor produced by Texas Instruments. It uses a single +5V supply and can measure AC and DC currents. It features high reliability, extremely low power consumption, 27kHz bandwidth, 3kVRMS isolation voltage and other characteristics.

USBN9603/USBN9604 Universal Serial Bus Full Speed Node Controller with Enhanced DMA Support is an integrated USB node controller produced by National Semiconductor Corporation.

AD8386 is a 10-bit, 12-channel output decimating LCD driver with features such as high voltage drive, output short-circuit protection, and high update rates.