Industrial

MNR34 Resistors Rev.E 1/4 Compact Chip Resistor Networks MNR34 (3216×4 size) is a resistor network product with convex electrodes, which makes it easy to check the fillet after soldering. It is compatible with a wide range of mounting equipment and is excellent for mounting using image recognition devices due to its squared corners. It can be mounted even more densely than four 3216 chips (MCR18), thereby reducing the number of parts and cost of mounting.

This document describes the features and characteristics of ROHM's compact 8-element chip resistor network MNR15 (0603x5 size), suitable for pull-up and pull-down resistors, with high-density mounting capability and compatibility with various mounting machines.

MNR12 is a 2-chip rectangular chip resistor network produced by ROHM, which has the characteristics of small size, light weight and high-density mounting.

MNR02 is a compact chip resistor network produced by ROHM. It is 60% smaller and 75% lighter than MNR12 in terms of area ratio and weight ratio respectively. It can be mounted more densely than two MCR01 chips and reduce the cost of mounting. It is also compatible with a wide range of mounting equipment.

This document describes the features and characteristics of ROHM's MCR50 Low Ohmic Thick Film Chip Resistors, such as high reliability, corrosion resistance, and suitability for re-flow soldering.

This data sheet provides information about the MCR25 series of low ohm thick film chip resistors, including resistance values, resistance accuracy, rated power, rated voltage, operating temperature range, etc.

This datasheet introduces Microchip's TC74 temperature sensor. The sensor has SOT-23-5 package and outputs 8-bit digital temperature data via a 2-wire SMBus/I2C compatible serial port. The sensor can be used in hard disk drives, PC card devices, low-cost thermostats, power supplies and other applications.

MCR18 series low ohmic thick film chip resistors are highly reliable resistors that use ruthenium oxide dielectric for superior resistance to the elements. The electrodes are made of thick film for high reliability.

The MCR10 is a low-ohm thick-film chip resistor produced by ROHM. The rated power is 1/4W. The features are high accuracy, high temperature resistance, and long life.

The document is about the RoHS Directive 2002/95/EC, which includes the specifications of the TC73 trimming potentiometer. It provides information on the electrical characteristics, environmental characteristics, and physical characteristics of the product. The standard resistance range of the trimming potentiometer is 500 to 1 megohm, with a resistance tolerance of ±30%. The minimum resistance is ≤ 1K Ohms with a maximum of 20 ohms. The contact resistance variation is 5% maximum, and the resolution is infinite adjustment. The product has a power rating of 0.05 watt at 50 °C, a temperature range of -25 °C to +85 °C, and a temperature coefficient of ±250 ppm/°C. It is also humidity resistant up to 95% RH for 500 hours. The trimming potentiometer is compatible with reflow processing and pick and place equipment, and it is supplied in 8 mm embossed tape for automatic assembly. It features a carbon element and is RoHS compliant.

The TC72 is a digital temperature sensor capable of reading temperatures from -55°C to +125°C. This sensor features a serial interface that allows communication with a host controller or other peripherals. The TC72 interface is compatible with the SPI protocol. The TC72 does not require any additional external components. However, it is recommended that a decoupling capacitor of 0.01 µF to 0.1 µF be provided between the VDD and GND pins. The TC72 can be used either in a Continuous Temperature Conversion mode or a One-Shot Conversion mode. The Continuous Conversion mode measures the temperature approximately every 150 ms and stores the data in the temperature registers. In contrast, the One-Shot mode performs a s

LTR50 is a high power chip resistor from Rohm that has higher welding strength, higher surge resistance and higher power tolerance.