Industrial

The LTC ®1448 is a dual rail-to-rail voltage output, 12-bit digital-to-analog converter (DAC). It includes rail-to-rail output buffer amplifiers and an easy-to-use 3-wire serial interface. It is available in 8-pin SO and PDIP packages and provides the smallest footprint of any dual 12-bit DAC. The LTC1448 has an external reference input pin (REF) and its outputs swing from 0V to REF. The REF input can be tied to VCC providing rail-to-rail operation from supplies of 2.7V to 5.5V. (For devices with internal reference see the LTC1446 data sheet.) The LTC1448 dissipates 2.5mW from a 5V supply. The low power supply current and the small SO-8 package make the LTC1448 i an excellent choice for high performance low power applications.

Low Noise, Low Power Signal Processing, Ultrasonic Amplifiers, Driving A/D Converters, Audio Amplifiers, Op Amps

LT1584/LT1585/LT1587 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed Low voltage fast response positive output three terminal adjustable regulator

This document mainly introduces the characteristics of LPV321/358/324 low-power operational amplifiers, including operating voltage range, output swing, input common-mode range, bandwidth, power consumption, etc.

LP2980 is a 50mA micropower low dropout regulator designed by TI. Using the optimized VIP (Vertically Integrated PNP) process, the LP2980 delivers unequaled performance in all key power design specifications.

The LMV232 dual RF detector is designed for RF transmit power measurement in mobile phones. This dual mean square IC is especially suited for accurate power measurement of RF signals exhibiting high peak-to-average ratios used in 3G and UMTS/CDMA applications. The LMV232 saves calibration steps and system certification and is highly accurate. The circuit operates with a single supply from 2.5 to 3.3V. The LMV232 contains a mean square detector with two sequentially selectable RF inputs. The RF input power range of the device has been optimized for use with a 20 dB directional coupler, without the need for additional external components. A single external RC combination between FB and OUT provides an externally configurable gain and LF filter bandwidth of the device. The device has two digital interfaces. A shutdown function is available to set the device in a low-power shutdown mode. In case SD = HIGH, the device is in shutdown, if SD = LOW the device is active. The Band-Select function controls the selection of the active RF input channel. In case BS = HIGH, RFIN1 is active. In case BS = LOW, RFIN2 is active. The dual mean square detector is offered in an 8-bump micro SMD 1.5 x 1.5 x 0.6 mm package. This micro SMD package has the smallest footprint and height.

The document describes a square LED with dimensions of 5.0mm × 2.0mm, available in different light colors such as red, green, amber, and orange. The document provides information on the LED's absolute maximum ratings, electro-optical characteristics, and forward current directive characteristics.

LM6211 is a wide bandwidth, low noise op amp with a wide supply voltage range and a low input bias current. The device operates with a single supply voltage of 5V to 24V, is unity gain stable, has a ground-sensing CMOS input stage, and offers rail-to-rail output swing. The LM6211 is designed to provide optimal performance in high voltage, low noise systems. The device has a unity gain bandwidth of 20 MHz and an input referred voltage noise density of 5.5 nV/A, frequency 10 kHz. LM6211 achieves these specifications with a low supply current of only 1 mA. LM6211 has a low input bias current of 2.3 pA, an output short circuit current of 25 mA and a slew rate of 5.6 V/μs. LM6211 also features a low common-mode input capacitance of 5.5 pF which makes it ideal for use in wide bandwidth and high gain circuits. LM6211 is well suited for low noise applications that require an op amp with very low input bias currents and a large output voltage swing, like active loop-filters for wide-band PLLs. A low total harmonic distortion, 0.01% at 1 kHz with loads as high as 600 Ω, also makes the LM6211 ideal for high fidelity audio and microphone amplifiers. The LM6211 is available in the small SOT package, allowing the user to implement ultra-small and cost effective board layouts.

This file is a TI's LM2904, LM324 and LM358 operational amplifier introduction manual, which mainly introduces the characteristics, features, working principles and application scenarios of operational amplifiers.

The LM124 series is a quadruple high-gain frequency-compensated operational amplifier designed for single-supply operation over a wide range of voltages. It features 2kV ESD protection, wide supply ranges, low supply-current drain, large common-mode input voltage range, low input bias and offset parameters, large differential input voltage range, and internal frequency compensation.

This document introduces the coding rules and packaging specifications of the DE series polyester capacitors

LD1084 series is a 5A low dropout positive voltage adjustable and fixed type regulator, output voltage range 1.5V-12V.