Industrial

The document is about the introduction of GALEP-4 series programmers. It is a professional field programmer and supports EPROMs, EEPROMs, FLASH EPROMs, serial EEPROMs, Microcontrollers, GALs and PALCEs. It can read and program

The T7024 is a monolithic SiGe transmit/receive front-end IC with power amplifier, low-noise amplifier and T/R switch driver. It is especially designed for operation in TDMA systems like Bluetooth® and WDCT. Due to the ramp-control feature and a very low quiescent current, an external switch transistor for VS is not required.

7511MR2D red LED specifications, including external dimensions, maximum working voltage, maximum working current, maximum power consumption, working temperature range, storage temperature range, etc.

This document describes a product with a MPEG I/II-Layer 3 hardwired decoder, supporting multiple sampling frequencies and audio control features, as well as external storage interface and communication interface.

The 74V1G07 is an advanced high-speed CMOS SINGLE BUFFER (OPEN DRAIN) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology.

This datasheet provides detailed information on the 74LCX04 low voltage hex inverter, including operating voltage, package type, and pinout.

The CY74FCT163952 and CY74FCT163H952 are low-power, pin-compatible replacements for the LCX and LPT families, with 5V-tolerant inputs and outputs, 24 mA balanced-drive outputs, power-off disable outputs that permit live insertion, edge-rate control circuitry for reduced noise, FCT-C speed at 4.4 ns, latch-up performance that exceeds JEDEC Standard No. 17, typical output skew less than 250 ps, industrial temperature range of -40˚C to +85˚C, TSSOP (19.6-mil pitch) or SSOP (25-mil pitch), typical Volp (ground bounce) performance that exceeds Mil Std 883D, VCC = 2.7V to 3.6V, ESD (HBM) > 2000V, bus hold on data inputs, eliminates the need for external pull-up or pull-down resistors, devices with bus hold are not recommended for translating rail-to-rail CMOS signals to 3.3V logic levels

The 74F219 is a high-speed 64-bit RAM organized as a 16-word by 4-bit array. Address inputs are buffered to minimize loading and are fully decoded on-chip. The outputs are 3-STATE and are in the high-impedance state whenever the Chip Select (CS) input is HIGH. The outputs are active only in the Read mode. This device is similar to the 74F189 but features non-inverting, rather than inverting, data outputs.

The 74ALVCHS162830 is an address driver produced by PHILIPS. It has a bus hold function (3-state) and is designed for 2.3 V to 3.6 V VCC operation. The product is packaged in TVSOP and has a balanced ±12 mA output drive with low noise and low skew.

The 74ACTQ153 is a high-speed dual 4-input multiplexer with common select inputs and individual enable inputs for each section. It can select two lines of data from four sources. The two buffered outputs present data in the true (non-inverted) form. In addition to multiplexer operation, the ACTQ153 can act as a function generator and generate any two functions of three variables.

The 74ABT16241A 74ABTH16241A is a high-performance BiCMOS device from Philips Semiconductors that combines low static and dynamic power dissipation with high speed and high output drive. This device is a 16-bit buffer that is ideal for driving bus lines. The device features four Output Enables (1OE, 2OE, 3OE, 4OE), each controlling four of the 3-State outputs. Two options are available, 74ABT16241A which does not have the bus hold feature and 74ABTH16241A which incorporates the bus hold feature.

provides detailed information on the 6N138, 6N139 and HCPL-2730, HCPL-2731 optocouplers, including product features, application scenarios, technical indicators, etc.

The HS-1254RH is a ±5V, Rad Hard, monolithic, dual, current feedback amplifier that provides highly reliable performance in harsh radiation environments. Dielectric isolation and bonded wafer processing make this device immune to latch-up (SEL). Excellent dynamic characteristics, coupled with the disable function, make this amplifier well-suited for a variety of satel- lite system applications. The outputs have individual disable control pins that make it easy to multiplex wideband signals, putting the outputs in a high impedance mode and reducing the supply current per op amp down to 3mA (typical). Post radiation limits are fully speci

The document describes the specifications and characteristics of the MPR series metallized polypropylene film capacitors. These capacitors have very low dissipation factor, small and light. They are suitable for applications where high frequency, high voltage are required, such as electronic ballasts. The capacitors are coated with flame-retardant (UL94 V-0) epoxy resin and are RoHS compliant.