Industrial

The document describes the features and characteristics of the AT27C080 chip, including fast read access time, low power CMOS operation, JEDEC standard packages, high-reliability CMOS technology, rapid programming algorithm, etc.

The AT24C256B is a serial EEPROM memory with features including low-voltage and standard-voltage operation, internally organized as 32,768 x 8, a two-wire serial interface, Schmitt trigger, filtered inputs for noise suppression, bidirectional data transfer protocol, etc.

This document introduces the characteristics of the [brand] [product_name] [model] product. The product uses [technology] technology and supports [feature] features. It is suitable for [application] scenarios.

This catalog contains the Teccor Electronics thyristor product information, including product selection guide, product descriptions, circuit requirement diagram, product packages and more.

The AT45DB041B is an SPI compatible serial interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applica- tions. Its 4,325,376 bits of memory are organized as 2048 pages of 264 bytes each. In addition to the main memory, the AT45DB041B also contains two SRAM data buffers of 264 bytes each. The buffers allow receiving of data while a page in the main memory is being repro- grammed, as well as reading or writing a continuous data stream. EEPROM emulation (bit or byte alterability) is easily handled with a self-contained three step Read-Modify- Write operation. Unlike conventional Flash memories that are accessed randomly with multiple pages, the AT45DB041B supports page programming, allowing programming or erasing a single page in a single clock cycle.

Provides specifications for 898 and 899 dual-in-line thick film resistor networks.

The AT28C256 is a high-performance electrically erasable and programmable read-only memory from Atmel. It features a 150ns read access time and 440mW power consumption. The device has 32768 8-bit words of 256KB of storage space and uses Atmel's advanced non-volatile CMOS technology. The AT28C256 can be accessed like a static random-access memory for reading or writing, without the need for external components. The device contains a 64-byte page register to allow simultaneous writing of up to 64 bytes of data. During a write cycle, the addresses and 1 to 64 bytes of data are internally latched, freeing the address and data bus for other operations. After the start of a write cycle, the device will automatically write the address and data to the memory.

MT-RJ connectors are versatile connector systems with RJ-45 form factor, duplex ferrule. Increases port density required on computer and networking related hardware, panels, wall plates, and in closets by 50%. Meets TIA-568A standards. Low insertion loss: <.22 dB TYP MM <.19 dB TYP SM

SC Duplex Connectors & Adapters are fiber optic connectors that are available from Molex. They combine two widely accepted NTT-SC standard connectors and have low insertion loss and are rugged. They are suitable for use in telecommunications networks, data communication networks and Fibre Channel.

This document is the 8451-8453 type choke specification. The product uses high-loss ferrite materials for excellent high frequency noise absorption. It is suitable for digital equipment data lines.

The document describes the features and characteristics of the 2 AMP Positive Step-Down Integrated Switching Regulator produced by Power Trends, Inc., including high efficiency, wide input range, self-contained inductor, short-circuit protection, over-temperature protection, and fast transient response.

1.5 amp negative adjustable voltage regulator, approved to DESC standardized military drawing number 7703406

Matrix Multimedia Atmel AVR® Board EB19430 is a development board based on Atmel AVR® produced by Matrix Multimedia Limited.

The Atmel AVR STK500 is a starter kit and development system for Atmel’s AVR Flash microcontrollers. The STK500 gives designers a quick start to developing code on the AVR, combined with features for developing prototypes and testing new designs. The STK500 interfaces AVR Studio®, Atmel’s Integrated Development Environment (IDE) for code writing and debugging. The STK500 starter kit includes AVR Studio Software Interface, RS-232 Interface to PC for Programming and Configuration, Power Supply Regulator for 9V - 12V DC Power, Sockets for 8-, 20-, 28- and 40-pin AVR Devices, Serial In-System Programming (ISP) of AVR Devices, In-System Programmer for Programming AVR Devices in External Target Systems, Parallel and Serial High-voltage Programming of AVR Devices, 8 Push Buttons and 8 LEDs for General Use, All AVR I/O Ports Easily Accessible through Pin Header Connectors, RS232 Port for General Use, Expansion Connectors for Plug-in Modules and Prototype Area, On-board 2-megabit DataFlash® for Nonvolatile Data Storage, Software Upgradable from AVR Studio to Support Future AVR Devices, Flexible Clocking, Voltage and Reset System.