Industrial

This document describes the features and characteristics of a 4M-BIT single voltage 3V flash memory called MX29LV004T/B, including status reply, ready/busy pin, sector protection, minimum erase/program cycles, latch-up protection, boot sector architecture, low VCC write inhibit, and package type.

The MX27C512 is a 5V only, 512K-bit, ultraviolet Eras- able Programmable Read Only Memory. It is organized as 64K words by 8 bits per word, operates from a single +5volt supply, has a static standby mode, and features fast single address location programming.

This document is a specification for the MX23L2000 2M-bit MASK ROM chip. The chip features a bit organization of 256K x 8, fast access time of 150ns, low power consumption, and a supply voltage range of 2.7V to 3.6V.

This document is about the specifications of MVL-591G LED lamp, including the product's size, power, current, voltage and other parameters.

This is a PDF document about BRT (Bias Resistor Transistor). It is an integrated circuit that integrates two resistors, a series base resistor and a base-emitter resistor. The BRT can replace a single device and its external resistor bias network. The device uses SC-59 package, which is designed for low power surface mount applications.

The MT8880C/C-1 is a monolithic DTMF transceiver with call progress filter. It is fabricated in Mitel’s ISO2-CMOS technology, which provides low power dissipation and high reliability. The DTMF receiver is based upon the industry standard MT8870 monolithic DTMF receiver; the transmitter utilizes a switched capacitor D/A converter for low distortion, high accuracy DTMF signalling. Internal counters provide a burst mode such that tone bursts can be transmitted with precise timing. A call progress filter can be selected allowing a microprocessor to analyze call progress tones. A standard microprocessor bus is provided and is directly compatible with 6800 series microprocessors. The MT8880C-1 is functionally identical to the MT8880C except for the performance of the receiver section, which is enhanced to accept and reject lower signal levels.

This document introduces the features of the 256Mb: x4, x8, x16 DDR SDRAM produced by Micron Technology, Inc., including voltage, data transfer rate, storage capacity, etc.

This document introduces the MSP430x11x2 family of products, including the low supply voltage range, ultra-low power consumption, five power saving modes, fast wake-up, 16-bit RISC architecture and other features.

This document describes the features and characteristics of the semiconductor product MSM511000C/CL, including high integration, high-speed operation, and low-power consumption.

MSC23232D/DL-xxBS16/DS16 is a fully decoded, 2,097,152-word x 32-bit CMOS dynamic random access memory module composed of sixteen 4Mb DRAMs in SOJ packages mounted with sixteen decoupling capacitors on a 72-pin glass epoxy single-inline package.

This document is about MRF1047T1 technical data sheet, which details the features and characteristics of the product, including low noise characteristics, high current gain-bandwidth product, maximum stable gain, output third order intercept, etc.

FN6140.1 is a sensitive electrostatic discharge device that requires proper IC handling procedures. It is a CMOS programmable peripheral interface chip manufactured by Intersil, which can be used with many different microprocessors. It has 24 programmable I/O pins and can be used in three major modes of operation. The chip is compatible with 80C86, 80C88, and other microprocessors, with high performance and industry-standard configuration. The static CMOS circuit design ensures low operating power. Intersil's advanced SAJI process results in performance equal to or greater than existing functionally equivalent products at a fraction of the power.

The MOC306X-M and MOC316X-M devices consist of a GaAs infrared emitting diode optically coupled to a monolithic silicon detector performing the function of a zero voltage crossing bilateral triac driver. They are designed for use with a triac in the interface of logic systems to equipment powered from 115/240 VAC lines, such as solid-state relays, industrial controls, motors, solenoids and consumer appliances, etc.