Industrial

This document covers information about USBizi Chipset, specifications, tutorials and references.

This document describes the features and functionality of the DS2153Q E1 single-chip transceiver, including complete E1 (CEPT) PCM-30/ISDN-PRI transceiver functionality, on-board line interface for clock/data recovery and waveshaping, jitter attenuator, line build-outs for 120Ω and 75Ω lines, frame formats, dual on-board two-frame elastic store slip buffers, control port, CAS signaling extraction and insertion, detection and generation of remote and AIS alarms, programmable output clocks, fully independent transmit and receive functionality, full access to Si and Sa bits, three separate loopbacks for testing, and large counters.

The DS2153Q T1 Single-Chip Transceiver (SCT) contains all of the necessary functions for connection to E1 lines. The onboard clock/data recovery circuitry coverts the AMI/HDB3 E1 waveforms to a NRZ serial stream. The DS2153 automatically adjusts to E1 22 AWG (0.6 mm) twisted-pair cables from 0 to 1.5 km. The device can generate the necessary G.703 waveshapes for both 75-ohm and 120-ohm cables. The onboard jitter attenuator (selectable to either 32 bits or 128 bits) can eliminate jitter, ensuring high-quality reception.

The DS2152 T1 Enhanced Single-Chip Transceiver contains all of the necessary functions for connection to T1 lines, whether they be DS-1 long haul or DSX-1 short haul. It has complete DS1/ISDN-PRI transceiver functionality, can handle both long and short haul trunks, generates DSX-1 and CSU line build outs, supports D4, ESF, and SLC-96R formats, has dual onboard two-frame elastic store slip buffers that can connect to asynchronous backplanes up to 8.192 MHz, supports 8-bit parallel control port, can extract and insert robbed-bit signaling, detects and generates RAI and AIS alarms, has programmable output clocks for Fractional T1, fully independent transmit and receive functionality, integral HDLC controller with 16-byte buffers for the FDL, generates and detects in-band loop codes from 1 to 8 bits in length including CSU loop codes, contains ANSI 1's density monitor and enforcer, large path and line error counters including BPV, CV, CRC6, and framing bit errors, pin compatible with DS2154 E1 Enhanced Single-Chip Transceiver, operates on 5V supply, low power CMOS, and comes in a 100-pin 14mm2 body LQFP package.

This product is a T1 Single-Chip Transceiver, which can be used for DS-1 long haul or DSX-1 short haul lines. It has complete DS1/ISDN-PRI transceiver functionality, and the line interface can handle long-haul and short-haul trunks.

DS2149 is a fully integrated LIU for long-haul or short-haul T1 applications over twisted-pair installations. It interfaces to two twisted-pair lines—one pair for transmit and one pair for receive through an appropriate network interface. The device can be configured for control through software or hardware mode. Software control is accomplished over a serial port, in hardware mode; individual pin settings allow standalone operation. The device provides a precise, crystal-less jitter attenuator that can be placed in either the transmit or receive path.

This document mainly introduces the features of DS2149, including support for long-distance or short-distance T1 applications, support for hardware or software control, and support for a precise crystal-less jitter attenuator

The DS21458DK Design Kit is an easy-to-use evaluation board for the DS21458 quad T1/E1/J1 transceiver. The kit includes the DS21458 quad SCT, transformers, termination resistors, configuration switches, line protection circuitry, network connectors, and motherboard connectors. The DK101/DK2000 motherboard and Dallas' ChipView software provide point-and-click access to configuration and status registers from a Windows®-based PC. On-board LEDs indicate receive loss-of-signal and interrupt status. An on-board FPGA contains mux logic to connect framer ports to one another or to the DK2000 in a variety of configurations. Each DS21458DK is shipped with a free DK101 motherboard. For complex applications, the DK2000 high-performance demo kit motherboard can be purchased separately.

This is a user manual of ChipworkX Development System, mainly introduces how to run the project in the emulator and hardware, how to update the firmware

This document covers complete information about the ChipworkX™ Module and Development System, specifications, tutorials, and references.

ALFAT SoC processor concept, pin-out, specifications, commands, hardware integration guide and full information needed to implement a solution using this processor. A high performance FAT file system SoC processor with dual USB Host interfaces and 4-bit SD interface. Controlled through UART, SPI or I2C.

This is the user manual for the GHI Electronics ALFAT SoC Processor, a high-performance FAT file system SoC processor with dual USB Host interfaces and 4-bit SD interface. Controlled through UART, SPI or I2C.

This is a user manual for ALFAT SoC processor, including processor concept, pin-out, specifications, commands, hardware integration guide and etc.

This document introduces the concept, pin-out, specifications, commands, hardware integration guide and full information needed to implement a solution using the ALFAT SoC processor.

This document introduces the concept, pin-out, specifications, commands, hardware integration guide and full information needed to implement a solution using this processor