ATMEL Manuals

AT45DB081D is a 2.5V or 2.7V serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications. The AT45DB081D supports RapidS serial interface for applications requiring very high speed operation.

AT29C010A is a 5-volt-only in-system Flash programmable and erasable read only memory (PEROM). Its 1 megabit of memory is organized as 131,072 words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 70 ns with power dissipation of just 275 mW over the commercial temperature range. When the device is deselected, the CMOS standby current is less than 100 µA. The device endurance is such that any sector can typically be written to in excess of 10,000 times. To allow for simple in-system reprogrammability, the AT29C010A does not require high input voltages for programming. Five-volt-only commands determine the operation of the device. Reading data out of the device is similar to reading from an EPROM.

The TS80C31X2 is a ROMless version of the 80C31 compatible, high-performance CMOS single chip 8-bit microcontroller 80C51. The TS80C31X2 retains all the features of the TSC80C31 with 128 bytes of internal RAM, a 5-source, 4-priority level interrupt system, an on-chip oscillator and two timer/counters. In addition, the TS80C31X2 has a dual data pointer, a more versatile serial channel that facilitates multiprocessor communication (EUART) and a X2 speed improvement mechanism. The fully static design of the TS80C31X2 allows to reduce system power consumption by bringing the clock frequency down to any value, even DC, without loss of data. The TS80C31X2 has 2 software-selectable operating modes, including idle mode, power-down mode and power-off flag mode.

The AT26DF321 is a serial interface Flash memory device designed for use in a wide variety of high-volume consumer based applications in which program code is shad- owed from Flash memory into embedded or external RAM for execution. The flexible erase architecture of the AT26DF321, with its erase granularity as small as 4-Kbytes, makes it ideal for data storage as well, eliminating the need for additional data storage EEPROM devices. The physical sectoring and the erase block sizes of the AT26DF321 have been opti- mized to meet various application requirements.

AT28C64B is a high-performance electrically-erasable and programmable read- only memory (EEPROM). Its 64K of memory is organized as 8,192 words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers access times to 150 ns with power dissipation of just 220 mW. When the device is deselected, the CMOS standby current is less than 100 µA. The AT28C64B is accessed like a Static RAM for the read or write cycle without the need for external components. The device contains a 64-byte page register to allow writing of up to 64 bytes simultaneously. During a write cycle, the addresses and 1 to 64 bytes of data are internally latched, freeing the address and data bus for other operations. Following the initiation of a write cycle,

The AT26DF161A is a serial interface Flash memory device designed for use in a wide variety of high-volume consumer-based applications. It has a flexible erase architecture with a minimum erase granularity of 4 Kbytes, making it ideal for data storage. The physical sectoring and the erase block size make it a good choice for a variety of applications.

The AT28C256 is a high-performance electrically erasable and programmable read-only memory. It features fast read access time, automatic page write operation, fast write cycle times, low power dissipation, and more.

AT45DB021D is a 2.7V, serial-interface Flash memory ideally suited for a wide variety of digital voice-, image-, program code- and data-storage applications.

The AT27C256R is a low-power, high-performance 262,144-bit one-time programmable read-only memory (OTP EPROM). It features fast read access time and low-power CMOS operation. The product is available in industrial and automotive temperature ranges, and comes in various package options.

AT91SAM7A3-EK Evaluation Board is an evaluation board that can be used for evaluation and development of applications based on AT91SAM7A3

Atmel ATAVRMC100 BLDC motor control evaluation kit is an evaluation tool and development board for the AT90PWM3 AVR microcontroller from Atmel. The board includes power bridges for BLDC motors and can realize zero crossing voltage detection, hardware overcurrent detection and PWM output.

The document describes an ARM processor with internal high-speed flash, featuring high performance, high-density instruction set, and low power consumption. It also includes 512 KB or 256 KB of internal high-speed SRAM, supports an external bus interface, and has memory and reset controllers.

This document describes the features and characteristics of a high-performance, low-power AVR® 8-bit microcontroller. It utilizes an advanced RISC architecture with a powerful instruction set and single-clock cycle execution. The microcontroller has nonvolatile program and data memories, as well as various peripheral features including timers/counters, PWM channels, ADC, and serial interfaces. Additionally, it includes a JTAG interface and software security lock.