STMicroelectronics Manuals

The TSL1014 is a 14+1 channel buffer used to buffer the reference voltage for gamma correction in thin film transistor (TFT) liquid crystal displays (LCD).

The STVM100 is a programmable VCOM adjustment solution for thin-film transistor (TFT) liquid-crystal displays (LCDs) to remove “flickers”. It is also used in e-paper and e-book applications to avoid the 'ghosting' effect (residual pixels after display refresh). It can replace a mechanical potentiometer, so that the factory operator can physically view the front screen when performing the VCOM adjustment. This significantly reduces labor costs, increases reliability, and enables automation. The STVM100 provides a digital I2C interface to control the sink current output (IOUT). This output drives an external resistive voltage divider, which can then be applied to an external VCOM buffer. Three external resistors R1, R2, and RSET determine the highest and lowest value of the VCOM. An increase in the output sink current will lower the voltage.

TSL1018 is an 18+1 channel buffer used to buffer the reference voltage for gamma correction in TFT liquid crystal displays (LCD). It features wide supply voltage range, low operating current, high output current, and industrial temperature range.

STV7733 is a high-voltage, row/column driver IC with 320 tri-level (high-voltage, medium voltage and ground) power outputs. It can operate at 90V and supports logic supply range of 2.5V to 3.3V. It is suitable for COG, COF and TCP solutions.

The STV7622 is a data driver for Plasma Display Panels (PDP) designed in the ST’s proprietary BCD high-voltage technology. It controls up to 192 outputs via an input data bus (3, 6 or 2 × 3-bits wide) operating at up to 60MHz. This large number of outputs reduces the number of connections between the controller board and the data driver ICs. The STV7622 contains a new logic input stage that minimizes EMI resulting from the transmission of high speed TTL or LVCMOS data and clock signals. This new input stage is RSDS compliant. It enables increasing the operating frequency without compromising noise immunity. The input data bus is configured by dedicated input pins.

The STV7623 is a 1-bit x 480 shift register with dual rail high voltage/medium current output, with global blank and polarity control. The maximum shift frequency starts from 1 MHz for a 1.8 V type input signal, up to 10 MHz for a 3.3 V type input signal. This generic device can be used for segmented/dot matrix electroluminescent displays to drive an array of organic electronic transistors, or for technologies related to e-Paper/e-Reader/digital signage solutions. The device can be daisy-chained for various display resolutions.

The GS-R400 series is a versatile family of high current, high voltage step-down switching voltage regulators from Panasonic. This series features 4A of maximum output current, 46V of maximum input voltage and 4V of maximum drop-out voltage. In addition, this series also provides soft start, remote logic inhibit/enable, remote output voltage sense, non-latching overload and short circuit protection as well as crow-bar output overvoltage protection.

GS-R400/2 series is a family of high current, high voltage step-down switching regulators. The series has 4A max output current, 40V max input voltage, 4V max dropout voltage, soft start, non-latching short circuit protection, crow-bar output overvoltage protection etc.

This document describes the features and characteristics of the SPAC265-3W AC-DC switch mode power supply, including wide range input voltage, high MTBF, low standby power, etc. The product complies with various international standards and is suitable for appliance, industrial, and communication applications.

This is a 10 A, 600 V short-circuit rugged IGBT intelligent module with short-circuit rugged IGBT, negative temperature coefficient, 3.3V, 5V, 15V CMOS/TTL input comparators, under-voltage lockout, internal bootstrap diode, interlocking function, DBC substrate, etc. It is suitable for home appliances, 3-phase inverters and other applications.

This document describes STGIPL14K60 SLLIMM™ (small low-loss intelligent molded module) IPM, a 3-phase inverter with 15A, 600V short-circuit rugged IGBT features.

This STGIPS14K60 SLLIMM™ (small low-loss intelligent molded module) IPM, 3-phase inverter - 14 A, 600 V short-circuit rugged IGBT is an intelligent power module from ST that provides a compact, high performance AC motor drive in a simple, rugged design. Combining ST proprietary control ICs with the most advanced short-circuit- rugged IGBT system technology, this device is ideal for 3-phase inverters in applications such as home appliances and air conditioners.

STGIPS20K60 is an IPM 18 A, 600 V 3-phase IGBT inverter bridge including control ICs for gate driving and free- wheeling diodes. It features short-circuit rugged IGBTs, VCE(sat) negative temperature coefficient, 3.3 V, 5 V, 15 V CMOS/TTL inputs comparators with hysteresis and pull down / pull up resistors, undervoltage lockout, internal bootstrap diode, interlocking function, smart shutdown function, comparator for fault protection against over temperature and overcurrent, DBC leading to low thermal resistance, and isolation rating of 2500 Vrms/min.

STGIPS10K60T is a 600V short-circuit rugged IPM module produced by ST company with a current carrying capacity of 10A. It is suitable for home appliances, industrial motor drives and other applications.