STMicroelectronics manuals, page 301
ST AN2459 APPLICATION NOTE handbook
This document describes the application of digital power factor correction technology in tube lamp ballasts and other digital power supplies controlled by an 8-bit microcontroller. It focuses on power control and ballast protection.
ST AN2510 APPLICATION NOTE handbook
This application note introduces the L6585D control IC, a new PFC control IC for electronic ballasts. This IC integrates both PFC and half-bridge sections, and embeds a wide range of features to provide an energy saving and cost effective solution.
ST AN2524 APPLICATION NOTE handbook
This application note describes a demo board able to drive a 54 W linear T5 fluorescent lamp. The ballast control is done by the L6585D that integrates PFC and half-bridge control circuits, the relevant drivers, and the circuitry able to manage all lamp operating phases (pre-heating, ignition and run mode). Protections against main failures (lamp disconnection, anti-capacitive mode, PFC over-voltage) are guaranteed and obtained with a minimum number of external components. Finally, the electronic solution allows better control of the filament current and lamp voltage during pre-heating with the unquestionable benefit of increasing the mean lamp life.
ST AN2590 handbook
This document describes a 20W dimmable CFL ballast solution that can completely replace incandescent lamps in formal dimming systems. The dimmer controlled range is 20% - 100% of full light output without changing the formal triac dimmer. Compared to the formal CFL solution, this solution not only provides energy savings, but also higher reliability and a much longer operating life.
ST AN2708 handbook
This document describes a high-efficiency, high power factor, low THD and digital dimming electronic ballast designed to drive 2X36 W T8 tube lamps.
ST AN2771 handbook
2x58 W/T8 or 2x36 W/T8 fluorescent lamp ballast demonstration board driven by STMicroelectronics' L6585D
ST AN2870 handbook
The L6585DE is a combo IC for electronic ballasts that offers the designer a high performance PFC stage, high capability half bridge high voltage drivers, a fully programmable control and an enhanced set of protections.
ST AN2654 handbook
ST AN2056 handbook
This document describes a new device introduced by ST Microelectronics called SaTCR-1 (Satellite Channel Router), which is able to translate a transponder to any location in the satellite bandwidth (950-2150 MHz). Multiple SaTCR devices coupled with band-pass filters and RF matrix allow to combine transponders from different polarizations and bands on a single coaxial cable. The purpose of this document is to describe the AN2056 protocol extension used to control a LNB based on SCR technology.
ST AN4123 handbook
The STEVAL-ISV015V1 is a demonstration board mounting the SPV1040 device (solar energy harvester) as input stage and the LD39050PUR device (low noise and low quiescent current voltage regulator) as output stage. It targets any portable application powered by USB supply and merges the capability of the SPV1040 device to maximize the power extraction from solar modules with the high precision voltage regulation of the LD39050 device.
ST AN4069 handbook
This document introduces 5V and 12V power line protection based on STEF05 and STEF12 electronic fuses. These electronic fuses are designed to monitor the output current and input voltage and protect the electronic circuitry from overcurrent and overvoltage. They have programmable turn-on time to control the inrush current during startup and hot-swaps. When an overload condition occurs, the electronic fuse limits the output current to a predefined safe value. If the abnormal overload condition persists, it goes into an open state, disconnecting the load from the power supply. Both devices are equipped with a thermal protection circuit.
ST AN4062 handbook
This application note describes the peripheral firmware examples provided for the STM32F0DISCOVERY Kit. These ready-to-run examples are provided to help the user get started quickly with STM32F0xx peripherals and STM32F0DISCOVERY board hardware. Preconfigured projects for EWARM, MDK-ARM, TrueSTUDIO and TASKING toolchains are provided for each example. These examples are included in the firmware applications package available for download on www.st.com/stm32f0discovery. Users are advised to first read the document Getting started with software and firmware environments for the STM32F0DISCOVERY Kit (UM1523) to familiarize themselves with the STM32F0DISCOVERY Kit.
ST AN4050 handbook
The STEVAL-ISV012V1 is a demonstration board that mounts the SPV1040 (solar energy harvester) as the input stage and the L6924D (Li-Ion battery charger) as the output stage. It targets any portable application powered by lithium-ion batteries and merges the capability of the SPV1040 to maximize the power extraction from the solar module with the linear regulation of the L6924D, to optimize the battery charge and to protect the load while reducing the power dissipation at the bottom.
ST AN4044 handbook
This application note explains how to use floating-point units (FPU) with STM32F405/07xx and STM32F415/417xx microcontrollers
ST AN4032 handbook
This application note describes how to use the STM8SVLDISCOVERY to drive a standard HD44780 2-line LCD display. The example uses a LCD display driver that is as generic as possible and can be reused with any STM8 device. The example uses the popular 2 x 16 format of LCD display, but other LCD display modules based on compatible ST7066 or KS0066U controllers can also be used.