STMicroelectronics Manuals

VND5E008AY-E is a double channel high-side driver with analog current sense for automotive applications. It features power limitation for inrush current management, very low standby current, 3.0V CMOS compatible input, etc.

L99PM72PXP is a high performance power management system IC with embedded LIN and high speed CAN transceiver supporting CAN Partial Networking

The L99DZ81EP is a microcontroller driven multifunctional door actuator driver for automotive applications. Up to two DC motors and four high-side drivers are supported. It features current monitor output, temperature warning and protection, open-load detection, overcurrent protection, programmable PWM control, STM standard serial peripheral interface (ST-SPI 3.0), and prepared for additional fail-safe path for H-Bridge Applications.

The TDA7706 is a highly integrated tuner for AM/FM car-radio applications, featuring FM, AM, and weather band reception. It has a fully integrated VCO for worldwide tuning, a high-performance PLL for fast RDS system, integrated AM-LNA and PIN diodes, automatic self-alignment for FM front-end pre-selection filter and image rejection, integrated IF filters with high selectivity, dynamic range, and adaptive bandwidth control. It also offers drift-free Digital-IF signal processing with high performance, RDS demodulation with group and block synchronization, a high-performance stereo decoder with noise-blanker, a digital interface for HD Radio™ reception with digital audio blending, a fully programmable DSP core, I2C bus-controlled, I2S input/output digital audio interfaces, and operates on a single 5V supply. It comes in an LQFP64 package.

This is a data brief of STA662 AM/FM, DAB/DAB+/DMB-A, DRM multi-standard digital radio receiver

This data brief provides detailed information on the STA610, a highly integrated AM/FM/HD/DRM/DAB car radio tuner. The tuner features quad-band, low phase noise VCO, high performance PLL tuning system, automatic self-alignment, SPI bus control and more.

The L6362 is a monolithic dual push pull Transceiver fully compliant to PHY2 (3 wires) supporting COM1 (4.8 kbaud), COM2 (38.4 kbaud) and COM3 (230.4 kbaud) modes.

STULPI01A STULPI01B is a high-speed USB ULPI transceiver that is fully compliant with USB 2.0 specification and ULPI 1.1 register set. It supports high-speed, full-speed, and low-speed modes of operation and features integrated termination and pull-up/pull-down resistors. The product is suitable for applications such as mobile phones, PDAs, MP3 players, digital cameras, etc.

This document describes the features and characteristics of the 54ACxxxx, 54ACTxxxx rad-hard advanced high-speed 5V CMOS logic series, including operating voltage, high speed performance, power dissipation, output characteristics, noise immunity, operating temperature, etc.

This document describes the features and characteristics of the STMicroelectronics 54VCXH163245 dual supply bidirectional level shifter, including dual supply, voltage range, 3-state output, internal limiting resistor, etc.

The PM8903 is a compact, high-efficiency, monolithic step-down switching voltage regulator which can deliver up to 3 A of continuous current. The IC minimizes external components and board space by incorporating low-resistance MOSFETs into the IC. It is used in applications including CPU, DSP and FPGA power supplies, distributed power supplies, and for general DC/DC converters. The PM8903 features an input voltage range of 2.8 V to 6 V, adjustable output voltage to as low as 0.6 V, PSKIP mode for optimizing efficiency at light load, undervoltage, overvoltage, overcurrent, and overtemperature protection, power good output, 1.1 MHz switching frequency which enables the use of a small inductor, low quiescent current when shut down (<15 µA), interleaving synchronization (up to two ICs), and a small VFQFPN16, 3x3 mm package.

This document introduces recommendations to manually mount EnFilmTM micro battery EFL700A39 on printed circuit board (PCB) for prototyping purposes

This is an application note of EVLVIP37LE5V3A, a new power module from ST. It supports wide input voltage range and 5V-3A output. It is suitable for various standby power applications.

This application note presents a reference design for a high-efficiency, high-power PD (up to 60 W input) power converter based on an active-clamp forward topology with self-driven synchronous rectification using the PM8803 as the main controller.

This application note provides an evaluation of the performance comparison between the SPV100x and two standard Schottky diodes, in order to supply proper guidelines for the correct use of both devices.