STMicroelectronics manuals, page 280
ST AN2815 Application note handbook
The PM6675AS is a high-efficiency step-down controller with an embedded 2A LDO regulator. It features fast transient response, selectable low-consumption mode, and low-noise mode.
ST AN2811 Application note handbook
Introduces the features and application of VIPER17HN for non-isolated LED constant current driver
ST AN2810 Application note handbook
The LED7707 LED driver is a high-efficiency monolithic boost converter and six controlled current generators (rows), specifically designed to supply LED arrays used in the backlighting of LCD panels. The device can manage an output voltage up to 36 V (i.e. ten white-LEDs per row). The generators can be externally programmed to sink up to 85 mA and can be dimmed via a PWM signal (1% of minimum dimming duty-cycle at 1 kHz can be managed). The device allows detection and management of open and shorted LED faults, and permits unused rows to be left floating. Basic protections (output overvoltage, internal MOSFET overcurrent and thermal shutdown) are provided.
ST AN2809 Application note handbook
The LED7706 is a high-efficiency LED driver chip from STMicroelectronics. It can provide up to 36V of power for LCD panel backlights and can be dimmed using a PWM signal.
ST AN2808 Application note handbook
The PM6670S is a complete DDR2/3 power supply regulator designed for portable applications to meet JEDEC specifications. It integrates a constant on-time (COT) buck controller, a 2 Apk sink/source low dropout regulator (LDO), and a 15 mA low noise buffered reference. The COT architecture ensures a fast transient response supporting both polymeric and ceramic output capacitors. An embedded integrator control loop compensates the DC voltage error caused by the output ripple. The 2 Apk sink/source linear regulator provides the memory termination voltage with a fast load transient response. The device is fully compliant with system sleep states S3, S4, and S5, setting the LDO output to high-impedance in the suspend-to-RAM state, and performing the tracking discharge of all outputs in the suspend-to-disk state.
ST AN2898 Application note handbook
PM6670AS is a complete DDR2/3 power supply regulator for portable applications designed to meet JEDEC specifications
ST AN2783 Application note handbook
The PM8800 demonstration kit is a highly integrated device that embeds an IEEE802.3af compliant powered device (PD) interface together with a PWM controller and support for auxiliary sources.
ST AN2782 Application note handbook
This application note presents a design solution for a 400 W fixed-off-time controlled PFC preregulator using the L6562A controller.
ST AN2761 Application note handbook
This document presents a solution for designing a transition mode PFC preregulator using the L6562A. The L6562A is the latest proposal from STMicroelectronics for low and middle power applications such as lamp ballasts, high-end adapters, flat TVs and monitors, and PC power supplies. It is also suitable for emerging markets that may require low-cost power factor correction. Based on a well-established architecture, the L6562A offers excellent performance that considerably enlarges its field of application.
ST AN2755 Application note handbook
This application note describes a demonstration board based on the transition-mode PFC controller L6562A and presents the results of its bench demonstration. The board implements a 400 W, wide-range mains input PFC pre-conditioner suitable for ATX PSU, flat screen displays, etc. In order to allow the use of a low-cost device like the L6562A at this power level, usually prohibitive for this device, the chip is operated with fixed-off-time control. This allows continuous conduction mode operation, normally achievable with more expensive control chips and more complex control architectures.
ST AN2754 Application note handbook
This document describes how to implement a constant current control to drive high- brightness LEDs by a step-down DC-DC converter voltage regulator.
ST AN2753 Application note handbook
The VIPer17 is an offline power converter that integrates an advanced PWM controller with built-in BCD6 technology and an 800V avalanche rugged vertical power MOSFET. The device is suitable for 6W output power with a wide range input voltage (85VAC-270VAC) or 10W output power with a single range input voltage (85VAC-132VAC or 175VAC-265VAC). It offers the advantages of using few external components, providing several switch mode power supply protections, and very low standby consumption in no-load condition.
ST AN2730 Application note handbook
AN2730 is an application note about ST's STCF06 chip, which introduces how to use this chip to design a single Flash LED driver.
ST AN2728 Application note handbook
The ST1S12 is a synchronous step-down DC-DC converter optimized for powering low-voltage digital cores in HDD applications.
ST AN2726 Application note
AN2726 application note introduces STEVAL-ISB006V1 evaluation board, which is specifically designed for STw4102 battery management integrated circuit