STMicroelectronics Manuals

The document introduces the universal socket boards from STMicroelectronics for programming ST microcontrollers. The socket boards are equipped with specific MCU package sockets and signal routing cards, and can be connected to programming tools via ICC, SWIM, or JTAG. The socket boards are available for different types of package and connector for ST 8 or 32-bit Flash microcontrollers. They are intended for small-scale microcontroller programming, such as prototypes in the development stage.

AD-ICD is an in-circuit debugging adapter for ST7FLITEUx applications. It features a 10-pin ICC connector and an ST7FLiteUx microcontroller in a DIP16 package. Additionally, the adapter provides a device adapter for target devices in a DIP8 package and an on-application connector (8-pin header) for target devices in an SO8 package.

This document is an introduction to the ST6-EMU2 emulator. It covers the product's features, functions, and application scenarios.

ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. It features 5V power supply, USB 2.0 compatible interface, support for SWIM and JTAG/SWD interfaces, and direct firmware update feature.

FL-101 FlashLINK JTAG Programmer is a FlashLINK JTAG programming cable for PSD and UPSD microcontroller families, supports IEEE 1149.1 JTAG signals (TCK, TMS, TDI, TDO), supports additional signals (TERR and TSTAT) to reduce programming time.

The document describes the features and characteristics of the ST7590 Narrow-band OFDM power line networking PRIME compliant system-on-chip.

This datasheet provides detailed information on the features and characteristics of the STEVAL-SCM001V1 RTC dongle, including its mechanical size, functionality, and GUI.

STA529 is a 2x100mW digital stereo power amplifier chip produced by STMicroelectronics, with analog or digital input, 2.0 multi-channel digital audio processor, FFX features.

The STA321MP is a four-channel digital audio system with an FFX™ driver. It features a high efficiency FFX™ class-D modulator, 100 dB dynamic range, two stereo channels with I²S input/output data interface, a 16-bit stereo ADC input with PGA and microphone biasing, a PDM input interface for MEMS microphones connection, analog and digital muxing/mixing capability, an eight-channel input sample rate converter (8 kHz to 192 kHz), four channels of 24-bit audio processing, flexible channel mapping and routing, various output configurations (2.0, 2.1, 4.0, Mono), an advanced four-channel programmable audio processor, including embedded CMOS bridge, pfStart for pop-free single-ended operations, dynamic range compressor, play and record simultaneous operation, pre and post mix stages, individual channel and master gain/attenuation, digital gain/attenuation (-105 dB to +36 dB in 0.5 dB steps), soft volume update and muting, selectable DC-blocking high-pass filter, selectable de-emphasis filter, up to 13 28-bit user programmable biquads (EQ) per channel, advanced noise-shaping technologies enabling low frequencies optimized processing, bass/treble tone control, ternary, binary or phase shift modulation, PWM output, headphone output with jack detector, and I²C control.

L9951 is a microcontroller-driven multifunctional rear door actuator driver for automotive applications. Up to two DC motors and two grounded resistive loads can be driven with three half bridges and two highside drivers. The integrated standard serial peripheral interface (SPI) controls all operation modes (forward, reverse, brake and high impedance). All diagnostic informations are available via SPI.

This data sheet provides a detailed overview of the STA3005 Dual-IF AM/FM digital radio receiver.

TDA7528 is a STMicroelectronics AM/FM front-end chip for IF sampling car-radio tuners

The L9374 is a four channel low side driver with integrated recirculation diodes. It features a programmable channel timer, clock monitor, detailed load diagnosis, etc.

The L9390 is a twelve output low side valve driver designed for use in an ABS/ESP vehicle system. All outputs are PWM configurable, while six out of twelve are current regulated. Each of the twelve outputs is open drain configured and has a built-in 35V clamp. Eight of the twelve have integrated active freewheeling diodes for active rectification of the PWM controlled load. In order to minimize electromagnetic emissions during load actuation, the possibility to control output slopes is provided. Two separate communication interfaces support SPI communication for configuration and diagnostics.

VL5510 is a high dynamic range CMOS sensor from STMicroelectronics. The sensor has a resolution of 1024 x 512 monochrome and 5.6µm x 5.6µm high dynamic pixels. It supports parallel video data output interface, high-speed serial link interface, I2C control interface, SPI slave control interface, UART control interface, SPI master interface.