TEXAS Manuals

SN54ABT16373A, SN74ABT16373A are 16-bit transparent D-type latches with 3-state outputs designed specifically for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. These devices can be used as two 8-bit latches or one 16-bit latch. When the latch-enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs are latched at the levels set up at the D inputs. A buffered output-enable (OE) input can be used to place the eight outputs in either a n

SN54ABT16374A, SN74ABT16374A are 16-bit edge-triggered D-type bidirectional flip-flops with 3-state outputs specifically designed for driving highly capacitive or relatively low-impedance loads. They are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers. These devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock (CLK) input, the Q outputs of the flip-flop take on the logic levels set up at the data (D) inputs.

SN54ABT16541 and SN74ABT16541A are noninverting 16-bit buffers composed of two 8-bit sections with separate output-enable signals.

This data sheet provides detailed information about SN54ABT16543, SN74ABT16543 16-bit registered transceivers.

16-bit bus transceivers and registers with 3-state outputs

SN54ABT16657 and SN74ABT16657 are 16-bit transceivers with parity generators/checkers and 3-state outputs. They feature state-of-the-art EPIC-ΙΙB BiCMOS design that significantly reduces power dissipation and exceeds JEDEC standard JESD-17 latch-up performance. The products have distributed VCC and GND pin configuration to minimize high-speed switching noise. They utilize a flow-through architecture for optimized PCB layout. The high-drive outputs (–32-mA IOH, 64-mA IOL) provide strong output capabilities. Package options include plastic 300-mil Shrink Small-Outline (DL) and Thin Shrink Small-Outline (DGG) packages, as well as 380-mil Fine-Pitch Ceramic Flat (WD) package with 25-mil center-to-center spacings.

The SN54ABT16952 and SN74ABT16952 are 16-bit registered transceivers with 3-state outputs. They feature state-of-the-art EPIC-ΙΙB BiCMOS design that significantly reduces power dissipation. The latch-up performance exceeds 500mA per JEDEC Standard JESD-17. The typical VOLP (Output Ground Bounce) is less than 1V at VCC = 5V, TA = 25°C. The distributed VCC and GND pin configuration minimizes high-speed switching noise. The flow-through architecture optimizes PCB layout. The outputs have high-drive capability (-32mA IOH, 64mA IOL). Package options include plastic 300-mil shrink small-outline (DL) and thin shrink small-outline (DGG) packages, as well as a 380-mil fine-pitch ceramic flat (WD) package with 25-mil center-to-center spacings.

The TLV2354, TLV2354Y is a four-channel differential comparator designed by Texas Instruments with low supply voltage, low power consumption, high input impedance and fast response time, suitable for single-supply applications

The TPS5102 is a dual, high efficiency controller designed for notebook system power requirements. Under light load conditions, high efficiency is maintained as the controller switches from the PWM mode to the lower frequency Skip mode. These two operating modes, along with the synchronous-rectifier drivers, dead-time, and very low quiescent current, allow power to be conserved and the battery life extended, under all load conditions. The resistor-less current protection and fixed high-side driver voltage simplify the system design and reduce the external parts count. The wide input voltage range and adjustable output voltages allow flexibility for using the TPS5102 in notebook power supply applications.

The TPS755xx family of 5-A low dropout (LDO) regulators contains four fixed voltage option regulators with integrated power-good (PG) and an adjustable voltage option regulator. These devices are capable of supplying 5 A of output current with a dropout of 250 mV (TPS75533). Therefore, the device is capable of performing a 3.3-V to 2.5-V conversion. Quiescent current is 125 µA at full load and drops down to less than 1 µA when the device is disabled. The TPS755xx is designed to have fast transient response for large load current changes.

This document describes the features and characteristics of the µA78M00 series positive-voltage regulators, including high output current up to 500mA, no external components required, internal thermal-overload protection, and short-circuit current limiting.

The datasheet introduces the features and characteristics of the TL750L and TL751L series low-dropout voltage regulators. The series regulators have options of 5V, 8V, 10V, and 12V, and the TL751L series also has an enable (ENABLE) input. When ENABLE is high, the regulator output is in the high-impedance state. This gives the designer complete control over power up, power down, or emergency shutdown. The TL750L and TL751L series are low-dropout positive-voltage regulators specifically designed for low-power applications.

This document is the TL780 series positive voltage regulator manual, which introduces the features and characteristics of the series products, including ±1% output tolerance, ±2% output tolerance, thermal shutdown, internal short circuit current limiting, pinout identical to µA7800 series, improved version of µA7800 series

The document introduces the features of the TI MSP430 series ultra-low-power microcontrollers, including supply voltage range, power consumption, clock module configuration, timer A, comparator, programming method, etc.

PCI1031 PCI-TO-PC CARD16 CONTROLLER UNIT SCPS008B is a product of Texas Instruments, supporting PCI Local Bus Specification 2.1, compatible with 5-V/3.3-V PC Card16 Cards, supporting Two PC Card Slots With Hot Insertion and Removal, and meeting 1995 PC Card Standard.