This page provides manuals, user guides, handbooks, instructions, specification, instruction, maintenance manual for TEXAS Motherboard, Data Converters, Wireless connection, Power Management, ...
This document is the user's guide for the Texas Instruments MSP-FET430P140 Flash Emulation Tool. The tool is designed for the MSP430F13x/14x ultra-low power microcontroller. The document provides information on the kit contents and software installation process.
The UC5603 is an active terminator that complies with SCSI, SCSI-2, and SPI-2 standards. It provides 9 lines of termination and has a disconnect feature. It supports hot plugging and has current limit and thermal shutdown protection.
The SN65LBC171 and SN75LBC171 are monolithic integrated circuits designed for bidirectional data communication on multipoint bus-transmission lines. Potential applications include serial or parallel data transmission, cabled peripheral buses with twin axial, ribbon, or twisted-pair cabling. These devices are suitable for FAST–20 SCSI and can transmit or receive data pulses as short as 25 ns, with skew less than 3 ns. These devices combine three 3-state differential line drivers and three differential input line receivers, all of which operate from a single 5-V power supply. The driver differential outputs and the receiver differential inputs are connected internally to form three differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever
The ADS1174 and ADS1178 are multiple delta-sigma analog-to-digital converters with four/octal simultaneous sampling channels and data rates up to 52k samples-per-second. These devices offer high-speed and low-power operation, as well as high-performance AC and DC performance.
The TPS65810/TPS65811 is a single-cell Li-Ion battery and power management IC from TI. It supports a maximum charging current of 1.5A and integrates 8-channel A/D sampling system parameters. It supports single conversion, peak detection or average operating modes, and has software and hardware reset functions. It can set system parameters and access system status using the I2C interface, support AC adapter and USB port charging, and have interrupt functions and programmable masking signals system status modification to host.
The UCC5638 is a multimode SCSI terminator that provides a smooth transition into LVD SCSI and automatically detects the bus type and switches termination modes.
The TPS65150 is a power management chip for TFT LCD displays. It supports a wide input voltage range of 1.8V-6V, and has an internal 2A MOSFET switch. It supports both positive and negative output voltages, and the output voltage accuracy is <1%.
The document introduces the features and characteristics of the UC5603 chip, which is a chip that provides 9 lines of active termination for the SCSI bus. It supports hot plugging and has low channel capacitance and low standby power
This document is about UCC5686, a twenty-seven line active terminator for low-voltage-differential (LVD) SCSI networks. This LVD SCSI-only design allows the user to reach peak bus performance, while reducing system cost. The device is designed as an active Y-terminator to improve the frequency response of the LVD SCSI Bus.
The UCC5606 is a 9-line active terminator that complies with SCSI, SCSI-2, and SPI-2 standards. It operates from 2.7V to 5.25V and has a channel capacitance of 1.8pF during disconnect. The supply current in disconnect mode is only 0.5µA. It meets SCSI hot plugging requirements and features programmable termination resistance, trimmed termination current and impedance, as well as current limit and thermal shutdown protection.
The UCC5614 is a terminal driver for SCSI interface released by TI company. It can provide 9 lines of termination for the SCSI bus and support hot-plugging. The maximum operating voltage of UCC5614 is 5.25V, and the minimum operating voltage is 2.7V. When disconnected, the supply current of UCC5614 is only 0.5μA. UCC5614 also has ultra-low channel capacitance, which can effectively suppress signal interference.
The SN65LBC170 and SN75LBC170 are monolithic integrated circuits designed for bidirectional data communication on multipoint bus-transmission lines. Potential applications include serial or parallel data transmission, cabled peripheral buses with twin axial, ribbon, or twisted-pair cabling. These devices are suitable for FAST-20 SCSI and can transmit or receive data pulses as short as 25 ns, with skew less than 3 ns. These devices combine three 3-state differential line drivers and three differential input line receivers, all of which operate from a single 5-V power supply. The driver differential outputs and the receiver differential inputs are connected internally to form three differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever the
The SN75ALS170 and SN75ALS170A triple differential bus transceivers are monolithic integrated circuits designed for bidirectional data communication on multipoint bus transmission lines. It is designed for balanced transmission lines and the driver meets ANSI Standards EIA/TIA-422-B and RS-485 and both the driver and receiver meet ITU Recommendation V.11. The SN75ALS170A is designed for FAST-20 SCSI and can transmit or receive data pulses as short as 30 ns with a maximum skew of 5 ns. The SN75ALS170 and SN75ALS170A provide three bidirectional transceivers, using high-performance low-power Schottky circuitry, designed for multipoint transmission on long bus lines in noisy environments.
