TEXAS Manuals

The ADS8343 is a 16-bit, 4-channel serial output sampling analog-to-digital converter with features such as bipolar input range, pin-for-pin compatibility with the ADS7841 and ADS8341, single supply operation from 2.7V to 5V, 4-channel single-ended or 2-channel differential input, up to 100kHz conversion rate, 86dB SINAD, and a serial interface.

The OPA703 series of operational amplifiers are rail-to-rail input and output, single supply, and are specified and guaranteed over the supply range of ±2V to ±6V. The OPA703 series have low quiescent current, low offset voltage, and high gain bandwidth product, and are suitable for automotive, portable equipment, test equipment, and data acquisition applications.

SN5408, SN54LS08, SN54S08 SN7408, SN74LS08, SN74S08 QUADRUPLE 2-INPUT POSITIVE-AND GATES.

The SN74LVC1G07 is a single buffer/driver from TI with open drain output. It supports 1.65-V to 5.5-V VCC operation and has a maximum sink current of 32 mA. It can be used in partial power down applications.

SN65LVDS387, SN75LVDS387, SN65LVDS389 SN75LVDS389, SN65LVDS391, SN75LVDS391 is a high-speed differential line driver produced by TI company. It meets or exceeds the ANSI EIA/TIA-644 standard and is designed for signaling rates up to 630 Mbps with very low radiation (EMI). Low-voltage differential signaling with typical output voltage of 350 mV and a 100-Ω load. Propagation delay times less than 2.9 ns, output skew is less than 150 ps, part-to-part skew is less than 1.5 ns, each driver has a total power dissipation of 35 mW at 200 MHz, the driver is in high impedance when disabled or VCC < 1.5 V, the SN65 version bus-pin ESD protection exceeds 15 kV, and it is packaged in a thin shrink small-outline package with a 20-mil terminal pitch. Low-Voltage TTL (LVTTL) logic inputs are 5-V tolerant.

SN54AHCT595, SN74AHCT595 are 8-bit serial-in, parallel-out shift registers with 3-state output registers.

The SN74ALVC14 is a six-way Schmitt trigger inverter produced by Texas Instruments. It operates at a voltage of 2.3V to 3.6V and a temperature of -40℃ to 85℃.

SCBS682G is an octal buffer/driver with support for mixed-mode signal operation. It supports 5V input and output voltages as well as a 3.3V VCC voltage. It features low output ground bounce, support for unregulated battery operation, power-up 3-state support hot insertion, bus hold on data inputs, and more.

The THS306x amplifiers are high-voltage, high slew-rate current feedback amplifiers designed for low-distortion with a high slew rate of 7000 V/µs. They are ideally suited for applications requiring large, linear output signals such as video line drivers and VDSL line drivers.

The THS4061 and THS4062 are 180-MHz high-speed amplifiers, ideal for a wide range of applications including video, communication, and imaging. They offer 180-MHz bandwidth, 400 V/µs slew rate, and 40-ns settling time (0.1%). They have high output drive capability and low distortion.

The TLC220x is a precision, low-noise operational amplifier using Texas Instruments Advanced LinCMOS process. These devices combine the noise performance of the lowest-noise JFET amplifiers with the dc precision available previously only in bipolar amplifiers. The Advanced LinCMOS process uses silicon-gate technology to obtain input offset voltage stability with temperature and time that far exceeds that obtainable using metal-gate technology. In addition, this technology makes possible input impedance levels that meet or exceed levels offered by top-gate JFET and expensive dielectric-isolated devices. The combination of excellent dc and noise performance with a common-mode input voltage range that includes the negative rail makes these devices an ideal choice for high-impedance, low-level signal-conditioning applications in either single-supply or split-supply operation.

Texas Instruments (TI) has recently identified a problem in the product models listed above related to DLL clock-generation. The DLL may not startup properly when initiated, resulting in the audio master clock not functioning. This issue does not affect applications that do not enable the product’s DLL.

Introduces Texas Instruments' digital audio product SLWS106H, including product specifications and technical parameters.

The UC385 is a low dropout linear regulator that responds quickly to fast load changes. It has a precision onboard reference and excels at driving GTL and BTL buses. Due to its fast response to load transients, the total capacitance required to decouple the regulator's output can be significantly decreased compared to standard LDO linear regulators. The dropout voltage (VIN to VOUT) is only 490mV maximum and 350mV typical at a 5A load (0°C to 100°C). The onboard bandgap reference is stable with temperature and scaled for a 1.2V input to the internal power amplifier. The UC385 is available in fixed output voltages of 1.5V, 2.1V, or 2.5V. The output voltage of the adjustable version can be set with two external resistors. If the external resistors are omitted, the output voltage defaults to 1.2V.