Industrial

MMST6427 is an NPN surface mount Darlington transistor with epitaxial planar die construction. It is ideal for medium power amplification and switching applications, featuring high current gain and an ultra-small surface mount package.

MMBTA92LT1 is a high voltage PNP type transistor produced by ONSEMI. Its main parameters are: rated collector-emitter voltage VCEO is -300Vdc, rated collector-base voltage VCBO is -300Vdc, rated emitter-base voltage VEBO is -5.0Vdc, and rated collector current IC is -500mAdc.

The MM74HC4046 is a low power phase lock loop utilizing advanced silicon-gate CMOS technology to obtain high frequency operation both in the phase comparator and VCO sections.

The MIM-0KM2ASF SERIES is miniaturized infrared receivers for remote control and other appplications requiring improved ambient light rejection. The separate PIN diode and preamplifier IC are assembled on a single leadframe. The epoxy package contains a special IR filter. This module has excellent performance even in disturbed ambient light applications and provides protection against uncontrolled output pulses.

The MIC5012 is the dual member of the Micrel MIC501X driver family. These ICs are designed to drive the gate of an N-channel power MOSFET above the supply rail in high- side power switch applications. The 14-pin MIC5012 is extremely easy to use, requiring only a power FET and nominal supply decoupling to implement either a high- or low-side switch. The MIC5012 charges a 1nF load in 60µs typical. Operation down to 4.75V allows the MIC5012 to drive standard MOSFETs in 5V low-side applications by boosting the gate voltage above the logic supply. In addition, multiple, paral- leled MOSFETs can be driven by a single MIC5012 for ultra- high current applications. Other members of the Micrel driver family include the MIC5010 full-featured driver, MIC5011 minimum parts count driver, and MIC5013 protected 8-pin driver. For new designs, Micrel recommends the pin-compatible MIC5016 dual MOSFET driver.

This document is an introduction to the Mitel MH88622 product. It mainly introduces the features of the product, including dual line interface circuit, 2-4 wire conversion, constant current supply, battery supply to the line, current overload protection, etc.

MCR8/D is a reverse blocking thyristor designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half–wave, silicon gate–controlled devices are needed.

The MCP1603 is a high efficient, fully integrated 500 mA synchronous buck regulator whose 2.7V to 5.5V input voltage range makes it ideally suited for applications powered from 1-cell Li-Ion or 2-cell/3-cell NiMH/NiCd batteries.

The MCM64PC32 (256K) and MCM64PC64 (512K) are designed to provide a burstable, high performance, L2 cache for the Pentium microprocessor in conjunction with Intel’s Triton II chip set. The MCM64PC32 is configured as 32K x 64 bits and the MCM64PC64 is configured as 64K x 64 bits. Both are packaged in a 160 pin card edge memory module. Each module uses Motorola’s 3.3 V 32K x 32 BurstRAMs and one Motorola 3.3 V 32K x 8 FSRAM for the tag RAM. Bursts can be initiated with either address status processor (ADSP) or cache address status (CADS). Subsequent burst addresses are generated internal to the BurstRAM by the cache burst advance (CADV) input pin. Write cycles are internally self timed and are initiated by the rising edge of the clock (CLK0) input. Eight write enables are provided for byte write control. PD0-PD3 map into the Triton II chip set for auto-configuration of the cache control. Pentium-Style Burst Counter on Chip. Pipelined Data Out. 160 Pin Card Edge Module. Address Pipeline Supported by ADSP Disabled with Ex. All Cache Data and Tag I/Os are TTL Compatible. Three State Outputs. Byte Write Capability. Fast Module Clock Rate: 66 MHz. Fast SRAM Access Times: 15 ns for Tag RAM, 8 ns for Data RAMs. One-Cycle Deselect Data RAMs. Decoupling Capacitors for Each Fast Static RAM. High Quality Multi-Layer FR4 PWB with Separate Power and Ground.

MCH18 is a series of 1608(0603) size chip capacitors with high capacitance and small size. It is characterized by miniature, light weight, high capacitance achieved by thin and multi layer technology, lead-free plating terminal and no polarity.

This document is the user guide for HCS12 microcontroller MC9S12K family devices, covering MC9S12KT256, MC9S12KG256, MC9S12KG128, MC9S12KL128, MC9S12KC128, MC9S12KG64, MC9S12KL64, MC9S12KC64, and MC9S12KG32. The document describes the features and characteristics of the products.

The MC74LVQ138 is a high performance, 1–of–8 decoder/ demultiplexer operating from a 2.7 to 3.6V supply. High impedance TTL compatible inputs significantly reduce current loading to input drivers while TTL compatible outputs offer improved switching noise performance. The MC74LVQ138 is suitable for memory address decoding and other TTL level bus oriented applications.

MC54/74HC138A is the upgraded version of MC54/74HC138, which supports LSTTL output. This chip can decode three-bit address into eight outputs, and supports three selection functions: decoding, cascading and selection.

The MC33999 is a 16-channel low-side switch with a 24-bit serial input control. It is designed for a variety of applications including inductive, incandescent, and LED loads.

MC1489/D is a four-line EIA−232D receiver produced by ON Semiconductor. It has an input resistance of 3.0 k to 7.0 k�, an input signal range of ±30 V, an input threshold hysteresis characteristic, and can perform logic threshold shifting and input noise filtering