Industrial

BD2240G and BD2241G are low on-resistance N-channel MOSFET high-side power switches, optimized for Universal Serial Bus (USB) applications. BD2240G and BD2241G are equipped with the function of over-current detection, thermal shutdown, under-voltage lockout and soft-start.

The BDxxKA5 series are low-saturation regulators that are available for output currents up to 500mA. The output voltage precision is ±1%. These LDO regulators are offered in several output voltages and package lineups with or without ON/OFF switches (that set the circuit current to 0μA at shutdown). This series can be used for a broad spectrum of applications ranging from TVs and car audio systems to HDDs, PCs, and DVDs. There regulators have a built-in overcurrent protection circuit that prevents the destruction of the IC, due to output short circuits and a thermal shutdown circuit.

The document introduces a Square varistor element product from EPCOS, which features the High-EnergetiQ series Q14/Q20, maximum load capacity, and approvals from UL, CSA, and CECC.

This product is an automotive body control power management integrated circuit with 50V high breakdown voltage, suitable for on-board microcontrollers

Si9400DY is a P-channel 20-V (D-S) MOSFET manufactured by Vishay Siliconix with a typical on-resistance of 0.40 ohms and a rated current of 2.0 A.

This manual introduces the functions and characteristics of BA9743AFV, BA9744FV, BA9741F/FS devices, application circuits and so on.

The BAxxBC0 series is a low-saturation regulator with an output current of 1.0 A and an output voltage accuracy of ±2%. A broad output voltage range is offered, from 1.5V to 10V, and built-in overcurrent protection and thermal shutdown (TSD) circuits prevent damage due to short-circuiting and overloading, respectively.

This document describes a standard fixed output LDO regulator product with high accuracy output voltage, low saturation, built-in over-current protection circuit, overload protection circuit, and over-voltage protection circuit.

SHB-1608 is a multilayer chip ferrite bead produced by PAGE, which has good anti-interference performance and is suitable for abnormal oscillation prevention of high frequency amplifying circuits and noise suppression of digital equipment.

The SFH 3410 is a silicon NPN phototransistor manufactured by Texas Instruments, especially suitable for applications in the range of 350nm to 970nm. The product has a SMT package, no base pin, and is suitable for vapor phase and IR reflow soldering. It is only available on tape and reel.

This document introduces the BD6062GU 1A Flash LED Driver IC product features and applications. The product supports 2wire and 3wire control modes and can set pre-flash and flash timers. The maximum LED current can reach 1A. The product is used in the flash and lighting of mobile phone cameras.

The BD2802GU is a RGB LED driver specifically designed for decoration purposes. This RGB driver incorporates lighting patterns and illuminates without imposing any load on CPU. This RGB driver is best-suited for illumination using RGB LEDs and decoration using monochrome LEDs.

BD26502GUL is “Matrix LED Driver”, is suitable for cellular phone LED driver, can control 7x17(119 dot) LED Matrix, support SPI and I2C interface.

BD1604MUV,BD1604MVV is a backlight LED driver for small LCD panels, which is a charge pump type. The number of external devices is minimized.

SE4100L is a low power GPS receiver that supports L1 signal reception at 1575.42MHz. The chip uses a low IF architecture and integrates amplifier, oscillator, mixer and demodulation functions. The external component count is low, requiring only a 16.368MHz crystal and 11 passive components in its minimum configuration. The chip uses a 24-pin LPCC package and has a power consumption of only 30mW. SE4100L supports two digitally controlled shutdown modes, which can completely power off the chip or only power off the 16MHz clock supply to the baseband processor. SE4100L also supports a switchable gain LNA, which can be used with a local passive antenna or a remote active antenna without changing the circuit configuration. The on-chip VCO and PLL generate the required LO frequency and are locked to an external crystal.