Industrial

BD6538G is a single channel high side power switch IC for USB devices and memory cards, with a low ON resistance Nch power MOSFET. It integrates various safety functions such as over current detection, thermal shutdown, under voltage lock out, and soft start function for power supply port protection.

BD6934FV is a 1-channel half-bridge pre-driver produced by ROHM Co., Ltd., for 125kHz drive, with a built-in oscillation circuit and driving current adjustment function

BD6941FM is a 1.25A reversible motor driver from ROHM, which can control a DC motor in four modes (Forward, Reverse, Standby, Brake) corresponding to two control logic inputs.

BD7003NUX, BD7004NUX are dual channels, 300mA low-dropout voltage regulator output at each channel. The output voltage range is from 1.2V to 3.3V by operating range from 2.5V to 5.5V. The shutdown current is near the zero current which is suitable for battery powered device.

The BD80C0AFPS, BD90C0AFPS is a low saturation regulator with 1A output current, 8.0V/9.0V output voltage, ±1% high output voltage precision, low saturation PDMOS output, built-in over current protection circuit, built-in thermal shutdown circuit, low ESR capacitor and TO252S-3 package. Applications include audio-visual equipments, FPDs, televisions, personal computers or any other consumer device.

TMC2011A/TMC2111A are high-performance, byte-wide shift registers with programmable delay lengths. The TMC2011A can be programmed to any length between 3 and 18 stages. It offers a special split-word mode which allows for mixed delay lengths. The TMC2011A, constructed in low-power CMOS, is pin and function compatible with the bipolar TDC1011. The TMC2111A is a byte-wide shift register that can be pro-grammed to lengths of 1 to 16 stages. The TMC2011A and TMC2111A are fully synchronous, with all operations controlled by a single master clock. Input and output registers are positive-edge triggered D-type flip-flops. The length and mode controls are also registered. Both devices operate with a maximum clock rate of 40 MHz. Fabricated in a submicron CMOS process, the TMC2011A and TMC2111A are TTL-compatible, and are available in 24-pin CERDIP and Plastic DIP packages.

BD8112EFV-M is a white LED driver with the capability of withstanding high input voltage (36V MAX). This driver has 2ch constant-current drivers integrated in 1-chip, which each channel can draw up to 150mA max, so that high brightness LED driving can be realized. Furthermore, a current-mode buck-boost DC/DC controller is also integrated to achieve stable operation against voltage input and also to remove the constraint of the number of LEDs in series connection. The brightness can be controlled by either PWM or VDAC techniques.

The HS-800/810 Series of quartz crystal oscillators provide MECL 10K and 10KH series compatible signals in industry standard four-pin DIP hermetic packages. Systems designers may now specify space-saving, cost-effective packaged ECL oscillators to meet their timing requirements.

BD8132FV and BD8139AEFV are high-precision gamma correction voltage generation ICs with built-in DACs and serial communication control. They provide a single-chip solution with a high-precision 10-bit DAC, output amplifier, Vcom amplifier, and auto-read function.

This document describes a high-precision Gamma correction IC for TFT LCD panels, which features built-in DACs and provides a 1-chip solution with setting control via serial communications. It includes a high-precision 10-bit DAC and a buffer amplifier (12 channels).

The BD8153EFV is a system power supply IC for TFT panels. It is a single-chip IC that provides the four voltages required for TFT panels, namely logic voltage, source voltage, gate high-level voltage, and gate low-level voltage, thus constructing a TFT panel power supply with minimal required components.

This datasheet provides detailed information on the features and applications of the BD8151EFV,BD8157EFV power supply ICs

BD8163EFV is a system power supply IC for TFT panels from ROHM Co., Ltd. A 1-chip IC providing a total of four voltages required for TFT panels, i.e., logic voltage, sauce voltage, gate high-level, and gate low-level voltage, thus constructing a TFT panel power supply with minimal components required.

The BD8179MUV is a system power supply IC for TFT panels. It is a 1-chip IC that provides the three voltages required for TFT panels: source voltage, gate high-level voltage, and gate low-level voltage, thus constructing a TFT panel power supply with minimal components required.