Industrial

The datasheet provides a detailed introduction to the characteristics of VNB14NV04, VND14NV04, VND14NV04-1 and VNS14NV04, including linear current limitation, thermal shutdown, short circuit protection, integrated clamp, low current input pin, diagnostic feedback pin, ESD protection, direct access to Power MOSFET gate (analog driving) and compatibility with standard Power MOSFETs

VNS1NV04D is a fully autoprotected power MOSFET device with features like linear current limitation, thermal shutdown, short circuit protection, integrated clamp, low current drawn from input pin, diagnostic feedback through input pin, etc. It is designed for DC up to 50KHz applications and can replace standard power MOSFETs.

VNS3NV04D is a fully autoprotected power MOSFET with features such as linear current limitation, thermal shutdown, short circuit protection, integrated clamp, etc.

L9616 is a high performance CAN bus transceiver that meets the ISO/DIS 11898 standard and supports data rates up to 1Mbit/s. The device features short circuit protection, slope control, and high interference suppression.

VQN660SP is a monolithic device made by using STMicroelectronics VIPower M0-3 Technology, intended for driving resistive or inductive loads with one side connected to ground. This device has four independent channels. Built-in thermal shutdown and output current limitation protect the chip from over temperature and short circuit.

L5951 is a triple output multifunctional voltage regulator with J1850 interface for car radio.

The L9348 is a monolithic integrated quad low side driver realized in advanced Multipower-BCD technology. It is intended to drive inductive loads (relays, electromagnetic valves) in automotive and industrial applications. It features a wide input and output voltage range, output voltage up to 40V, output current capability of 2 x 5A and 2 x 3A, low power dissipation, integrated free-wheeling diodes for recirculation of inductive loads, low on-resistance, output short circuit current protection, real-time diagnostic functions, overtemperature shutdown, and signal and power-ground-loss shutdown.

The L9333 is a monolithic integrated quad low side driver intended to drive lines, lamps or relais in automotive or industrial applications.

The L9903 is a power MOS driver produced by ST. It supports the ISO 9141 interface and has overvoltage, undervoltage, short circuit, and thermal protection functions. It can be used in automotive electronics and other fields.

L9826 is a protected octal low-side driver IC designed for the automotive environment. It features 8 channels with 450mA output current capability, typical RDSON of 1.5Ω at TJ = 25 °C, parallel control for output 1 and 2, SPI control on all outputs, reset function, diagnostic through 8 bit SPI, intrinsic output voltage clamping of 50V (Typ) for protection of inductive load drive, short circuit current limitation and thermal shutdown for outputs 1 and 2, and overcurrent and short circuit shutdown for outputs 3 to 8. The L9826 is packaged in SO20.

The VN750SM is a high-side driver featuring CMOS compatible input, on-state open load detection, off-state open load detection, shorted load protection, under-voltage and over-voltage shutdown, protection against loss of ground and very low stand-by current

The VN920 is a single channel high-side solid-state relay. It features CMOS compatible input, proportional load current sense, shorted load protection, under-voltage and over-voltage shutdown, over-voltage clamp, thermal shutdown, current limitation, protection against loss of ground and loss of VCC, very low standby power dissipation and reverse battery protection.

The VN920SP is a high-side single-channel solid-state relay with the following features: CMOS compatible input, proportional load current sense, shorted load protection, under-voltage and over-voltage shutdown, over-voltage clamp, thermal shutdown, current limiting, protection against loss of ground and loss of VCC, very low standby power dissipation, reverse battery protected.

The VNB35NV04, VNP35NV04, VNV35NV04, and VNW35NV04 are monolithic devices designed in STMicroelectronics VIPower M0-3 Technology, intended for replacement of standard Power MOSFETS from DC up to 25KHz applications. Built in thermal shutdown, linear current limitation and overvoltage clamp protect the chip in harsh environments. Fault feedback can be detected by monitoring the voltage at the input pin.