STMicroelectronics manuals, page 87
ST M24256-125 handbook
This document describes the features and characteristics of the M24256-125 automotive 256-Kbit serial I²C bus EEPROM, including compatibility with all I2C bus modes, 256 Kbit EEPROM memory array, 64-byte page size, byte write within 5 ms, page write within 5 ms, single supply voltage of 2.5 V to 5.5 V, operating temperature range from -40 °C to +125 °C, random and sequential read modes, write protect of the whole memory array, enhanced ESD/latch-up protection, more than 1 million write cycles, more than 40-year data retention, RoHS compliant and halogen-free packaging.
ST M24512-125 handbook
The M24512-125 is a 512-Kbit automotive EEPROM from ST that uses the I²C bus and features compatibility with all I2C bus modes, fast write speed, single supply voltage, wide operating temperature range, multiple read/write modes, write protection, ESD/Latch-Up protection, high reliability, and more.
ST M95512-A125 M95512-A145 handbook
Automotive 512-Kbit serial SPI bus EEPROMs with high-speed clock.
ST M24LR64E-R handbook
M24LR64E-R is a 64-Kbit EEPROM with password protection, dual interface and energy harvesting, supports 400 kHz I²C bus and ISO 15693 RF protocol, working frequency is 13.56 MHz.
ST M95256-A125 M95256-A145 handbook
M95256-A125 and M95256-A145 are automotive 256-Kbit serial SPI bus EEPROMs with high-speed clock.
ST M95128-125 handbook
M95128-125 is a 128-Kbit serial SPI bus EEPROM with high-speed clock from ST.
ST M95320-A125 M95320-A145 handbook
M95320-A125/A145 is a 32Kbit serial SPI bus EEPROM with high-speed clock. It features 32Kbits (4Kbytes) of EEPROM, 32 bytes of page size, 1/4, 1/2 or whole memory write protection, an additional write-lockable page (Identification page), high clock frequency 20MHz (VCC≥4.5V), 10MHz (VCC≥2.5V), 5MHz (VCC≥1.8V), and Schmitt trigger inputs for noise filtering.
ST M24C64-A125 handbook
The M24C64-A125 is a 64-Kbit serial I²C bus EEPROM from STMicroelectronics that is compatible with all I2C bus modes, including 1 MHz, 400 kHz and 100 kHz. It supports 40 years data retention, 1.8V to 5.5V wide operating voltage range and 125 °C temperature range
ST M95128-A125 M95128-A145 handbook
The M95128-A125 M95128-A145 is a 128-Kbit serial SPI bus EEPROM produced by ST with a high clock frequency.
ST L6571 handbook
The L6571 is a high voltage half bridge driver with a built-in oscillator. The frequency of the oscillator can be programmed using an external resistor and capacitor. The internal circuitry allows the device to also be driven by an external logic signal. The output drivers are designed to drive external n-channel power MOSFET and IGBT. The internal logic ensures a dead time to avoid cross-conduction of the power devices. Two versions are available: L6571A and L6571B. They differ in the internal dead time: 1.25μs and 0.72μs (typical).
ST L6574 handbook
The L6574 is a high voltage driver designed for lamp ballast applications. It is manufactured with BCD OFF LINE technology to ensure voltage ratings above 600V. The L6574 is capable of driving two power MOS-FETs in a half bridge topology to drive and control a fluorescent bulb. It features a dedicated timing section for pre-heat and ignition of the lamp, as well as a sense op amp for closed loop control or protection. The integrated bootstrap section and clamping on VS make the L6574 suitable for low cost applications.
ST L6382D handbook
The L6382D is suitable for microcontrolled electronic ballasts, including a PFC stage and a half-bridge stage, as well as a power management unit (PMU) with a reference voltage output that can supply the microcontroller in any condition.
ST L6382D5 handbook
The L6382D5 is a power management unit for microcontrolled ballasts. It has 4 drivers for PFC, half-bridge and pre-heating MOSFETs, and a fully integrated power management for all operating modes.
ST L6585D handbook
L6585D Combo IC is a PFC and electronic ballast control IC with the following features: 1. Pre-heating and ignition stages can be independently programmed; 2. Ignition voltage can be controlled; 3. Over-current protection PFC in transition mode; 4. Programmable and precise End-of-life protection compliant with all ballast configurations; 5. Auto-adjusting half-bridge over-current control; 6. Automatic re-lamp; 7. 3% oscillator precision; 8. 1.2µs dead time; 9. PFC over-voltage protection and feedback disconnection; 10. Under voltage lock-out.
ST L6585DE handbook
This document describes the L6585DE model, which is a combo IC for power factor correction (PFC) and ballast control. It features over-current protection, over-voltage protection, feedback disconnection, under-voltage lockout, PFC choke saturation detection, THD optimizer, etc.