STMicroelectronics Manuals

This document is a data brief for the STEVAL-IPE015V1 single-phase energy metering demonstration board by STMicroelectronics. The demonstration board features class 0.5 accuracy, Vnom(RMS) of 140 to 300V, Inom/Imax(RMS) of 2/20A, and flin of 45 to 65Hz. It also includes tamper detection for power line systems, capacitive power supply, SPI interface connector, and is RoHS compliant.

The STEVAL-IPE017V1 is a single-phase class 0.5 accuracy demonstration board based on the STPM10 chip and a shunt resistor for energy metering. It is designed for power line systems with a nominal voltage of 140 to 300 VRMS, a nominal/current maximum current of 2/20 ARMS, a frequency range of 45 to 65 Hz, and an operating temperature range of -40 to +85 °C. This demonstration board features a capacitive power supply, SPI interface connector, and is RoHS compliant.

The STEVAL-IPE018V1 is a single-phase energy metering demonstration board released by ST company, based on the STPM10 chip, with a class 0.5 accuracy, an rated voltage of 140 to 300 V, an rated current of 2 to 20 A, a frequency of 45 to 65 Hz, capacitive power supply, and RoHS compliance.

Introduces the STEVAL-IFP020V1 PLC (for industrial automation) digital output solution using a 2.5 A single high-side smart power switch based on the L6370Q

This document describes a double output SMPS module for power line applications, using the ALTAIR04-900 primary controller. The module features universal input mains range, double output voltage, optoless constant voltage-constant current output regulation, etc.

The STEVAL-IFP021V1 demonstration board is based on the STEF05 and STEF12 electronic fuses (E-Fuses). It features input voltages of 5V and 12V, continuous current of 3.6A each, adjustable slew rate for output voltage, overvoltage clamp, undervoltage lockout, programmable short-circuit current limit, overload current limit, controlled output voltage ramp, thermal latch protection, fault condition flag, and enable pin.

This document describes a 3000W photovoltaic converter for grid-connected applications. The converter has a wide input and output voltage range, high efficiency, and significant reduction in production costs.

The STEVAL-IHM035V1 is a power board designed to drive a high voltage/low power 3-phase brushless motor. It utilizes the ST IPM STGIPN3H60 (SLLIMM™-nano) for compact size and efficient power dissipation. The board is compatible with synchronous or asynchronous brushless motors (PMSM and ACIM) and can be interfaced with any ST MCU control board to implement a complete motor drive.

STEVAL-TLL006V2 is a new high-power LED driver demo board for single flash with I²C interface based on STCF06 (with motherboard based on µPSD).

This data sheet introduces the EVL150W-ADP-SR 12V-150W resonant converter features, such as universal input mains range, output voltage, mains harmonics, standby mains consumption, efficiency, EMI, safety, dimensions, PCB, etc

The document introduces STEVAL-ILD003V2, an analog wall dimmer based on TS820 for CFL/LED lamps, with a dimming range of 20-350W, meeting RoHS standard

This document is the datasheet of STEVAL-IPR002V1. It introduces the features of the product, including dual communication interfaces (RF and I2C) of M24LR64 EEPROM, temperature, motion (MEMS), humidity and light (photo diode) parameters recording, two operation modes (RFID mode and I2C mode), 20mm x 40mm inductive antenna, and Android NFC application DatalogV3

The Keil starter kit for STM32F4 series microcontrollers (STM32F407IG MCU) is a complete, cost-effective solution for starting application development and evaluating the STMicroelectronics STM32F4 series ARM Cortex™-M4 processor-based microcontrollers. It provides all the hardware and software you need to start developing applications for the STM32 ARM core-based families of microcontrollers.