intersil Manuals

1N120BND is a 5.3A, 1200V, NPT series N-Channel IGBT with Anti-Parallel Hyperfast Diode manufactured by Intersil. It is ideal for many high voltage switching applications operating at moderate frequencies where low conduction losses are essential, such as: AC and DC motor controls, power supplies and drivers for solenoids, relays and contactors.

The HFA1150 is a high-performance, wideband, fast settling op amp built with Intersil's proprietary complementary bipolar UHF-1 process. The current feedback architecture delivers superb bandwidth even at very high gains (>300MHz at AV=10), and the low distortion and excellent video parameters make this amplifier ideal for communication and professional video applications. Though specified for ±5V operation, the HFA1150 operates with single supply voltages as low as 4.5V, and requires only 3.4mA of Icc in 5V applications (see Application Information section, and Application Note AN9891). For a lower power amplifier in a SOT-23 package, please refer to the HFA1155 data sheet.

The DG506A, DG507A, DG508A and DG509A are CMOS monolithic 16-Channel/Dual 8-Channel and 8-Channel/Dual 4-Channel Analog Multiplexers, which can also be used as demultiplexers. An enable input is provided. When the enable input is high, a channel is selected by the address inputs, and when low, all channels are off. A channel in the ON state conducts current equally well in both directions. In the OFF state each channel blocks voltages up to the supply rails. The address inputs and the enable input are TTL and CMOS compatible over the full specified operating temperature range. The DG506A, DG507A, DG508A and DG509A are pinout compatible with the industry standard devices.

This document describes the AC loop of RSLIC18, including architectural description and voltage feed current sense.

HUF76409D3, HUF76409D3S 17A, 60V, 0.071 Ohm, N-Channel, Logic Level UltraFET Power MOSFET is a low on-resistance power MOSFET produced by Intersil.

ISL6295 is a low voltage fuel gauge IC from Intersil. It measures, stores and reports all critical parameters required for rechargeable battery monitoring with a minimum of external components. It precisely measures charge/discharge current as well as voltage and temperature of a battery pack.

EL4332 is a high-performance triple 2:1 video switch amplifier from Intersil. It supports TTL/CMOS compatible A/B control, 3ns switching time and 300MHz bandwidth, which can meet the performance requirements of the fastest component video systems. EL4332 uses a narrow 16-pin small outline package and operates at a standard ±5V supply voltage.

X60008B-41, X60008C-41, X60008D-41 Precision 4.096V FGA™ Voltage Reference offers outstanding long-term stability and very low power consumption.

X40410, X40411, X40414, X40415 4kbit EEPROM Dual Voltage Monitor with Integrated CPU Supervisor is a low power CMOS device produced by Intersil. It has 4kbits of EEPROM and 2-wire interface, and can monitor 5V to 0.9V of voltage range. It is used in communication equipment, routers, switches, disk arrays, networks, etc.

The ISL6269B is a Single-Phase Synchronous-Buck PWM controller featuring Intersil's Robust Ripple Regulator (R3) technology that delivers truly superior dynamic response to input voltage and output load transients.

ISL6252, ISL6252A is a battery charger controller for Li-Ion/Li-Ion polymer batteries from Intersil, supporting 2, 3, and 4 series Li-Ion cells, high efficiency synchronous buck topology, low side MOSFET emulates a diode at light loads to improve the light load efficiency and prevent system bus boosting.

ISL28270, ISL28273, ISL28470 Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO) Instrumentation Amplifiers with IREC

ISL6256, ISL6256A is a highly integrated battery charger from Intersil. It has automatic power source selection function and can be used to power notebook computers.

The HIP4082 is a medium frequency, medium voltage H-Bridge N-Channel MOSFET driver IC from Honeywell Company. It is suitable for PWM motor control and UPS applications. The device has a flexible input protocol that can drive all possible switch combinations except those that may cause a shoot-through condition. HIP4082's reduced drive current allows smaller packaging and it has a much wider range of programmable dead times (0.1 to 4.5µs), making it ideal for switching frequencies up to 200kHz. The HIP4082 does not contain an internal charge pump, but does incorporate non-latching level-shift translation control of the upper drive circuits. This set of features and specifications is optimized for applications where size and cost are important.

The ICL7667 is a dual monolithic high-speed driver designed to convert TTL level signals into high current outputs at voltages up to 15V. Its high speed and current output enable it to drive large capacitive loads with high slew rates and low propagation delays. With an output voltage swing only millivolts less than the supply voltage and a maximum supply voltage of 15V, the ICL7667 is well suited for driving power MOSFETs in high frequency switched- mode power converters. The ICL7667’s high current outputs minimize power losses in the power MOSFETs by rapidly charging and discharging the gate capacitance. The ICL7667’s inputs are TTL compatible and can be directly driven by common pulse-width modulation control ICs.