TEXAS Manuals

This document is the datasheet of CDCR83 DIRECT RAMBUS CLOCK GENERATOR product released by Texas Instruments (TI). It describes the features and characteristics of the product in detail.

This document describes the features of Harris Semiconductor SCHS122I, including wide analog input voltage range, low on resistance, low crosstalk, fast switching and propagation speeds, wide operating temperature range, etc.

The CD74HC377 is an octal D-type flip-flops with a buffered clock (CP) common to all eight flip-flops. All the flip- flops are loaded simultaneously on the positive edge of the clock (CP) when the Data Enable (E) is Low.

The document describes the features and characteristics of Harris Semiconductor SCHS146F, including data output selection, I/O port or memory selector, enable inputs, etc. The product has low power consumption, high speed, and high noise immunity.

The CD4071B, CD4072B, and CD4075B types are supplied in 14-lead hermetic dual-in-line ceramic packages (F3A suffix), 14-lead dual-in-line plastic packages (E suffix), 14-lead small-outline packages (M, MT, M96, and NSR suffixes), and 14-lead thin shrink small-outline packages (PW and PWR suffixes).

The LPV321/358/324 devices are the most cost-effective solutions for applications where low voltage, low-power operation, space saving, and low price are needed.

PCI1031 PCI-TO-PC CARD16 CONTROLLER UNIT SCPS008B is a product of Texas Instruments, supporting PCI Local Bus Specification 2.1, compatible with 5-V/3.3-V PC Card16 Cards, supporting Two PC Card Slots With Hot Insertion and Removal, and meeting 1995 PC Card Standard.

The document introduces the features of the TI MSP430 series ultra-low-power microcontrollers, including supply voltage range, power consumption, clock module configuration, timer A, comparator, programming method, etc.

This document is the TL780 series positive voltage regulator manual, which introduces the features and characteristics of the series products, including ±1% output tolerance, ±2% output tolerance, thermal shutdown, internal short circuit current limiting, pinout identical to µA7800 series, improved version of µA7800 series

The datasheet introduces the features and characteristics of the TL750L and TL751L series low-dropout voltage regulators. The series regulators have options of 5V, 8V, 10V, and 12V, and the TL751L series also has an enable (ENABLE) input. When ENABLE is high, the regulator output is in the high-impedance state. This gives the designer complete control over power up, power down, or emergency shutdown. The TL750L and TL751L series are low-dropout positive-voltage regulators specifically designed for low-power applications.

This document describes the features and characteristics of the µA78M00 series positive-voltage regulators, including high output current up to 500mA, no external components required, internal thermal-overload protection, and short-circuit current limiting.

The TPS755xx family of 5-A low dropout (LDO) regulators contains four fixed voltage option regulators with integrated power-good (PG) and an adjustable voltage option regulator. These devices are capable of supplying 5 A of output current with a dropout of 250 mV (TPS75533). Therefore, the device is capable of performing a 3.3-V to 2.5-V conversion. Quiescent current is 125 µA at full load and drops down to less than 1 µA when the device is disabled. The TPS755xx is designed to have fast transient response for large load current changes.

The TPS5102 is a dual, high efficiency controller designed for notebook system power requirements. Under light load conditions, high efficiency is maintained as the controller switches from the PWM mode to the lower frequency Skip mode. These two operating modes, along with the synchronous-rectifier drivers, dead-time, and very low quiescent current, allow power to be conserved and the battery life extended, under all load conditions. The resistor-less current protection and fixed high-side driver voltage simplify the system design and reduce the external parts count. The wide input voltage range and adjustable output voltages allow flexibility for using the TPS5102 in notebook power supply applications.

The TLV2354, TLV2354Y is a four-channel differential comparator designed by Texas Instruments with low supply voltage, low power consumption, high input impedance and fast response time, suitable for single-supply applications

The SN54ABT16952 and SN74ABT16952 are 16-bit registered transceivers with 3-state outputs. They feature state-of-the-art EPIC-ΙΙB BiCMOS design that significantly reduces power dissipation. The latch-up performance exceeds 500mA per JEDEC Standard JESD-17. The typical VOLP (Output Ground Bounce) is less than 1V at VCC = 5V, TA = 25°C. The distributed VCC and GND pin configuration minimizes high-speed switching noise. The flow-through architecture optimizes PCB layout. The outputs have high-drive capability (-32mA IOH, 64mA IOL). Package options include plastic 300-mil shrink small-outline (DL) and thin shrink small-outline (DGG) packages, as well as a 380-mil fine-pitch ceramic flat (WD) package with 25-mil center-to-center spacings.