ANALOG Manuals

MTV211 is a mobile TV one-chip receiver launched by Analog Devices. It supports ISDB-T 1-seg. reception and UHF RF input (Ch13 ~ 62, 470 ~ 770 MHz). It adopts low-IF architecture and has a sensitivity of -97 dBm (typ.).

The document describes the features of Analog Devices' low-IF tuner IC ITD3020 Rev.2.5 for dual-band DAB and FM receivers. It is a single-chip integrated tuner that eliminates all surface acoustic wave (SAW) filters and covers the entire Band-III (174 ~ 245 MHz), L-band (1450 ~ 1592 MHz), and FM (88 ~ 108 MHz). It has an operating dynamic range of -102 ~ -10 dBm, ultra-low power consumption, on-chip regulators, adjustable bandwidth low-pass filter, integrated IF variable gain amplifier for direct connection to digital demodulators, and other features. It is ideal for mobile DAB receivers and FM applications.

This is a single-chip synthesized tuner for terrestrial DMB and FM receivers. It features a low-IF single-conversion architecture that eliminates all SAW filters. It covers the entire Band-III (174 ~ 245 MHz) and FM (88 ~ 108 MHz) bands, has an operating dynamic range of -102 ~ -10 dBm, and consumes ultra-low power of only 100 mW. It has 2.85 V single-supply on-chip regulators, an on-chip fast switching fractional-N PLL, an on-chip low phase noise and wide frequency range VCO, an on-chip bandwidth-adjustable low pass filter, an integrated IF variable gain amplifier for direct connection to digital demodulators, noise/linearity optimization through internal RF RSSI and AGC loop, an adjustable take-over point, and is ideal for mobile TV receivers and terrestrial DMB applications. It has an I2C serial bus interface and a small 40-QFN package (6 × 6 mm2).

This is a low power mobile TV tuner IC for ISDB-T digital TV receiver. It features a single chip synthesized tuner with low IF single conversion architecture, eliminating all SAW filters.

ADMTV300 is a single chip synthesized tuner for T-DMB, dual-band DAB and FM receiver, which adopts a low-IF single-conversion architecture that eliminates all SAW filters.

ADSMV202 is a low power mobile TV tuner IC that is compatible with ISDB-T (1/3seg) and features ultra low noise figure, ultra low power consumption and ultra small size

ADMTV102 is a RF tuner IC for DVB-H, DVB-T, DTMB and CMMB. It is a single-chip synthesized tuner designed for dual-band mobile TV applications. ADMTV102 features a zero-IF single-conversion architecture that eliminates the need for SAW filters. It covers the entire UHF Band IV/Band V (470 MHz to 862 MHz). Typical AGC dynamic range is -102 dBm to 0 dBm. Low power consumption is 200 mW (UHF). ADMTV102 features a fast switching fractional-N PLL, low phase noise and wide frequency range VCO, bandwidth-adjustable low-pass filter, integrated baseband VGA for direct connection to digital demodulators, noise/linearity optimization through internal RF AGC loop, adjustable take-over point, I2C serial bus interface, small 5 mm × 5 mm, 32-lead lead frame chip scale package (LFCSP) and minimal external components.

AD5821 is a 120mA, 10-bit, I2C® DAC produced by Analog Devices, which can be used in consumer and industrial devices.

The AD5398 is a single 10-bit DAC with 120 mA output current sink capability. It features an internal reference and operates from a single 2.7 V to 5.5 V supply. The DAC is controlled via a 2-wire (I2C-compatible) serial interface that operates at clock rates up to 400 kHz. The AD5398 incorporates a power-on reset circuit, which ensures that the DAC output powers up to 0 V and remains there until a valid write takes place.

The ADD8502 is an integrated, high accuracy, programmable grayscale generator. Two sets of five output reference voltages are mask programmed to 0.2% resolution. The outputs switch between the two sets of five levels. The reference levels are selected from a 512 tap resistor network using a via mask. ADD8502 includes two serially addressable, 10-bit digital-to-analog converters (DACs) and five fast, low current buffers. The dual DACs set the endpoint voltages applied to the resistor network to adjust for flicker and range.

This document describes the features and characteristics of the high-performance, 12-bit, 12-channel decimating LCD DecDriver® AD8387 product.

The AD8386 is a 10-bit, 12-channel output decimating LCD driver with features such as high voltage drive, output short-circuit protection, high update rates, and low static power dissipation.

AD8385 is a 10-bit, 12-channel, LCD decimator with level shifters that features high voltage drive, output short-circuit protection, and high update rates.

AD8384 is a 10-bit, 6-channel, decimating LCD DecDriver® with Level Shifters from Analog Devices.

The document describes the low-cost 10-bit, 6-channel output decimating LCD DecDriver® AD8383 Rev. 0, which features high voltage drive, output short-circuit protection, high update rates, low static power dissipation, etc.