ANALOG Manuals (Industrial)

EVAL-AD1555/56EB is an evaluation board for the AD1555 and AD1556 24-bit differential ADC chip-set

File format: PDF Size:1266 KB

This document is an introduction document about DAC8143 12-Bit Serial Daisy-Chain CMOS D/A Converter, which introduces the features and characteristics of the product

File format: PDF Size:198 KB

The ADG3241 is a 2.5 V or 3.3 V, single digital switch. It is designed on a low voltage CMOS process, which provides low power dissipation yet gives high switching speed and very low on resistance. This allows the input to be connected to the output with very low switching delay.

File format: PDF Size:208 KB

The ADE7756 is a high accuracy, low power energy metering IC that supports IEC 687/1036 standards. It supports sampled waveform data and active energy, and has digital power, phase, and input offset calibration functions. It also has an on-chip temperature sensor and supports SPI-compatible serial interface.

File format: PDF Size:359 KB

The ADD8704 is a single-supply quad operational amplifier that has been optimized for today’s low cost TFT LCD notebook and monitor panels. Output channels A and D swing to the rail for use as end-point gamma references. Output channels B and C provide high continuous and peak current drive for use as VCOM or repair amplifiers; they can also be used as midpoint gamma references. All four amplifiers have excellent transient response and have high slew rate and capacitive load drive capability.

File format: PDF Size:271 KB

The AD9767 is a dual port, high speed, two channel, 14-bit CMOS DAC. It integrates two high quality 14-bit TxDAC+ cores, a voltage reference and digital interface circuitry into a small 48-lead LQFP package. The AD9767 offers exceptional performance, including 14-bit resolution, 125 MSPS update rate, low power consumption of 50mW in dual port or interleaved data mode, excellent SFDR and IMD performance, and 0.1% gain and offset matching.

File format: PDF Size:471 KB

The AD9281 is a complete dual channel, 28 MSPS, 8-bit CMOS ADC. It is optimized specifically for applications where close matching between two ADCs is required (e.g., I/Q channels in communications applications). The 28 MHz sampling rate and wide input bandwidth will cover both narrow-band and wide-band applications.

File format: PDF Size:418 KB

The document describes the features and characteristics of the AD848 and AD849, which are high speed, low power monolithic operational amplifiers. The AD848 has a gain bandwidth of 725 MHz and a supply current of 4.8 mA, suitable for applications with closed loop gains of 5 or greater. The AD849, on the other hand, is fully decompensated and has a gain bandwidth of 175 MHz and an input voltage noise of 3 nV/√Hz, making it suitable for specific applications. Both products can be used in cable drivers, 8- and 10-bit data acquisition systems, video and RF amplification, and signal generators.

File format: PDF Size:248 KB

AD8322 is a low-cost, digitally controlled variable gain amplifier that supports DOCSIS standard for reverse path transmission gain. It can be programmed in 6 dB steps over a 42 dB range via SPI interface. At 60 dBmV output, the distortion is low, –58dBc SFDR@21MHz, –56dBc SFDR@42MHz. The output noise level is –46dBmV with a bandwidth of 180MHz. The supply voltage is 5V.

File format: PDF Size:550 KB

The AD7890 is a 12-bit ADC chip launched by Analog Devices in 1996. It features fast conversion speed and low power consumption. The AD7890 has 8 single-ended analog input channels and supports three input ranges of -10V, 0V to -4.096V, and 0V to -2.5V. The AD7890 also integrates a track/hold amplifier and a reference voltage, and supports a high-speed serial interface up to 10MHz.

File format: PDF Size:307 KB

The AD5255 is a 3-channel digital potentiometer with nonvolatile memory. It features dual 512-position and single 128-position channels, offering 25kΩ or 250kΩ full-scale resistance. It has a low temperature coefficient, nonvolatile memory, linear increment/decrement, and I2C-compatible serial interface. The AD5255 is suitable for applications such as mechanical potentiometer replacement, LED brightness adjustment, and programmable gain and offset control.

File format: PDF Size:393 KB

AD2S81A/AD2S82A is a variable resolution monolithic resolver-to-digital converter that provides an analog signal proportional to velocity, which can be used to replace a tachogenerator. The converter features a one-chip solution, user-settable resolution, ratiometric tracking conversion, and user-settable dynamic performance.

File format: PDF Size:204 KB

The AD22057 is a single-supply difference amplifier for amplifying and low-pass filtering small differential voltages (typically 100 mV FS at a gain of 40) from sources having a large common-mode voltage.

File format: PDF Size:198 KB

This document describes the features and characteristics of a precision shunt voltage reference called AD1580 with a voltage output of 1.2V. It has a wide operating range, high initial accuracy, low temperature drift, and low output impedance. It is suitable for applications with input currents ranging from 50µA to 10mA.

File format: PDF Size:167 KB

This document describes the features and characteristics of the AD15700 product, including a 16-bit A/D converter, 1 MSPS speed, 14-bit D/A converter, 80 MHz amplifiers, 30V/μs slew rate, and compatibility with SPI/QSPI/MICROWIRE/DSP.

File format: PDF Size:1002 KB

AD1555/AD1556 is a 24-bit low noise analog-to-digital converter (ADC) with a low noise programmable gain amplifier (PGA). The device features a fourth-order oversampled sigma-delta (O-S) modulator, which provides a large dynamic range, low input noise, and low distortion. AD1555/AD1556 employs a common-mode voltage (VCM) input, supporting input ranges from -2.25 V to +2.25 V. AD1555/AD1556 is powered from a single supply of 2.5 V to 5 V.

File format: PDF Size:427 KB

The AD15452 is a 12-bit 65 MSPS quad A/D converter with integrated signal conditioning optimized for antijam global positioning system receiver (AJ-GPS) applications.

File format: PDF Size:1456 KB

The AD15252 is a dual, 12-bit, 65 MSPS analog-to-digital converter (ADC). It features a differential front-end amplification, dual parallel output buses, out-of-range indicators, independent clocks, and is suitable for applications such as anti-jam GPS receivers, wireless and wired broadband communications, and communications test equipment.

File format: PDF Size:1473 KB

The document describes the functional and performance features of the AD14160/AD14160L Quad-SHARC Ceramic Ball Grid Array (CBGA) product, including processing capabilities of 480 MFLOPS Peak and 320 MFLOPS Sustained, 16 Mbit shared SRAM, 16 40 Mbyte/s link ports, and 8 40 Mbit/s independent serial ports.

File format: PDF Size:754 KB

The AD14160/AD14160L is a single-chip quad-core DSP device from Analog Devices that has a peak performance of 480MFLOPS and a sustained performance of 320MFLOPS.

File format: PDF Size:1593 KB