Marley AC102-1A/AC104-1A Cooling Tower Vibration Sensor Application Guide

Marley application guide on selecting, installing and wiring vibration sensors for cooling tower motors, gearboxes, drive shafts and fans, with AC102/AC104…


Marley AC102-1A/AC104-1A Cooling Tower Vibration Sensor Application Guide - cover page
Brand
Marley
Category
sensor
Document type
Application Note
Language
Chinese
Pages
4
File format
PDF
File size
355 KB
Published
09 November, 2026
Updated
09 November, 2026
MD5 checksum
1A8A7783DBE87D58D623581AB4E89CD9

About this manual

This Chinese-language application guide from Marley addresses the difficulties vibration analysts face when monitoring cooling towers, where most faults occur in gearboxes mounted in hard-to-reach, hazardous locations beneath the fan. It explains that permanent accelerometers on the motor and gearbox improve safety, reliability and equipment life, and describes where to place radial and axial sensors on the drive-train components.

The guide covers sensor selection (general-purpose AC102/AC104 for vibration above 30 CPM and low-frequency AC135/AC136 for above 12 CPM), IP66-rated A2A and B2A connectors with Teflon-jacketed or armored cables, stud mounting with hole-facing tools such as the MH117-1B, junction boxes including the MX102-4C and the 12-channel SB202-12A, frequency analysis points for motors, drive shafts, gearboxes and fans, and references for typical operating limits. Page 4 lists the contents and specifications of the 12-channel cooling tower kit. This manual is written in Chinese.

What's inside

  • Cooling tower drivetrain components
  • Vibration sensor selection
  • Sensor placement on motor and gearbox
  • Cables and connectors
  • Mounting hardware
  • Junction boxes
  • Frequency analysis
  • Warnings and operating limits
  • References

Specifications

AC102-1A sensitivity100 mV/g +/-10%
AC102-1A frequency response+/- 3 dB, 30-900,000 CPM (0.5 - 15,000 Hz)
AC102-1A dynamic range+/- 50 g peak
AC102-1A temperature range-50 to 121 °C
AC102-1A kit quantity8
AC104-1A frequency response+/- 3 dB, 30-600,000 CPM (0.5 - 10,000 Hz)
AC104-1A kit quantity4
SB202-12A inputs3 inputs per channel, 12 channels
SB202-12A outputsBNC jacks and military two-pin connectors
SB202-12A enclosureNEMA 4X (IP66)
SB202-12A temperature range-58 to 82 °C
CB111-A2A-030-Z cableYellow Teflon-coated cable with dual-socket military E QUAL two-pin connector, 30 ft

Frequently asked questions

Which sensors are suitable for low-frequency vibration measurements?

The special-purpose low-frequency sensors AC135 (top outlet) and AC136 (side outlet) are for measuring vibration above 12 CPM (0.2 Hz), while the general-purpose AC102 or AC104 covers values above 30 CPM (0.5 Hz).

How many vibration sensors can be installed on the motor and gearbox?

Up to 6 sensors on the motor and 6 on the gearbox — 4 radial and 2 axial on each. Radial sensors detect unbalance and misalignment, axial sensors detect misalignment, bearing faults and gear mesh.

What connector and cable protection is recommended in cooling tower environments?

IP66-rated connectors are recommended to keep out dust and water; use A2A Mil E QUAL connectors or B2A sealed entries with Teflon-jacketed or armored cables.

Where can typical application guidelines and operating limits be found?

In Chapter 10, "Cooling Tower Mechanical Components", of the Cooling Tower Handbook; these limits are based on the cooling tower's structural design and components.

Download PDF (355 KB)

More Marley Manuals


View all Marley manuals →