Industrial

AME, Inc.'s AME1086 is a 1.5A low-dropout positive voltage regulator with features such as low dropout voltage, wide adjustment range, and overcurrent and thermal protection.

This document is the technical specification sheet for AMD's product, describing the features and characteristics of the Am29F010B 1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory.

This solid brass padlock has internal standard security and is suitable for toolboxes, sports equipment, lockers, etc. It uses a key to lock and unlock and the keys are keyed alike with other padlocks in this suite. The padlock is made of solid brass with a 4.5mm hardened steel shackle, a 3-pin tumbler mechanism made from all rustproof components, automatic locking, Pracentric keyway, and 2 keys.

This document provides information on the features and characteristics of a product under development at Advanced Micro Devices, including single power supply operation, 0.35µm process technology, high performance, ultra-low power consumption, and flexible sector architecture.

This document introduces a variety of hasp and staple products from ABUS, suitable for securing garages, sheds, and industrial applications. These products are made of steel and have hardened steel hinge pins and staples. The concealed hinge pin and hidden screws deter opportunist thieves. The document also provides information on using these products with other ABUS products.

ABUS Halbzylinder with Underfloor box in white. Dimensions: 105 x 155 x 45mm, including decorative frame and 3 keys

2 Megabit (256 K x 8-Bit) CMOS 3.0 Volt-only, Boot Sector Flash Memory with Flexible Sector Architecture

The MLX90269 Absolute Integrated Pressure Sensor is programmable, with adjustable offset and sensitivity. It provides an output proportional to the applied pressure and is available in different pressure ranges.

This document describes the features and benefits of the MLX90255BA linear optical array, including 128 x 1 sensor-element organization, high linearity and uniformity, high sensitivity, special gain compensation, low image lag, etc.

This document is a datasheet for the MLX90247 product, describing its features and benefits, as well as its applications and ordering information.

MLX90240 is a discrete micromachined pressure sensor IC suitable for pressure ranges between 0 to 350mBar. It has a compact design, high long term stability and low cost, and is suitable for medical instrumentation, consumer appliances, sports equipment and other fields.

This document describes a 1-bit to 2-bit address driver designed for 2.3V to 3.6V VCC operation. Diodes to VCC have been added on the inputs to clamp overshoot. Active bus-hold circuitry holds unused or undriven inputs at a valid logic state. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. The outputs, which are designed to sink up to 12 mA, include series damping resistors to reduce overshoot and undershoot. The ALVCHS162830A is an improved version of the LVCHS162830 (non-A version) and has been optimized for lower power consumption and higher AC drive. Higher AC drive provides capability to drive loads with a faster edge rate. To ensure the high-impedance state during power up or power down, the output-enable (OE) input should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.

The MLX90224 series is a dual Hall effect latch with dual outputs, operating voltage range of 4.5V to 28V, and features such as phase/direction detection.

The MLX90217 self adjusting digital output rotary position gear tooth sensor is designed for use in automotive camshaft sensing as well as other speed sensing applications. It is designed to be used with a bias magnet south facing the back (non marked) side of the IC. The device has an open collector output which is short circuit protected. The MLX90217 is a sophisticated IC featuring an on chip 10 bit A/D Converter and logic that acts as a digital sample and hold circuit. A separate 4 bit A/D converter provides a fixed hysteresis. The 90217 does not have a chopper delay. The 90217 uses a single Hall plate which is immune to rotary alignment problems. The bias magnet can be from 50 to 400mT. As the signal is sampled, the logic recognizes an increasing or decreasing flux density. The output will turn on (BOP) after the flux has reached its peak and decreased by an amount equal to the hysteresis. Similarly the output will turn off (BOP) after the flux has reached its minimum value and increased by an amount equal to the hysteresis.

The MLX90210 is a pressure sensor IC from Melexis. It is suitable for pressure ranges between 0 to 1.0 Bar.