Industrial

The AT89S51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of In-System Programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the indus- try-standard 80C51 instruction set and pinout. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory pro- grammer. By combining a versatile 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT89S51 is a powerful microcontroller which provides a highly-flexible and cost-effective solution to many embedded control applications. The AT89S51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, two 16-bit timer/counters, a five-vector two-level inter- rupt, serial channel, low-power idle and power-down modes, interrupt recovery from power-down mode, fast programming time, flexible ISP programming (byte and page mode).

The MCP6021/1R/2/3/4 is an operational amplifier with the following features: rail-to-rail input/output, wide bandwidth, low noise, low offset voltage, mid-supply VREF, low supply current, total harmonic distortion, unity gain stable, wide power supply range, and suitable for various applications.

PC 5/ 4-STCL-7,62 is a product of German brand PHOENIX CONTACT. It is a connector component with a rated current of 41A, a rated voltage of 1000V, a screw connection and a green color.

TGHG series precision current sense resistors use state of the art technology to provide highly reliable, non inductive performance. This resistor is ideal for current shunt measurement.

The DHR-C10 AC/DC current transducer is a high-precision, low-power, small-sized, large-output current sensor. It adopts the Hall effect principle, and uses the iron oxide magnetic core and the bipolar transistor magnetic coupling to convert the large current signal to a low-current signal that can be used for measurement and control systems.

This document describes the features and characteristics of Schurter's 99 power entry modules/combination elements KM, KMF, including ultra-compact design, innovative EMC shielding, pre-wired single elements, etc.

This document is about the product MSTBT 2,5/ 3-ST from PHOENIX CONTACT GmbH & Co. KG. The product is a plug component with a nominal current of 12A, nominal voltage of 250V, pitch of 5mm, 3 positions, screw connection, and green color. The product is WEEE/RoHS compliant.

This datasheet provides basic information of SFH 325 and SFH 325 FA NPN silicon phototransistor, including package, dimension, pin diagram, characteristic, maximum value, minimum value, typical value, application etc.

KLS 13 3 100 Straight plug 3-pole stereo headphone jack, meets JISC 6560 standard, 2.5mm connector, with kink protection and solder terminals

The document introduces the 6.35 mm Klinkensteckverbinder product that complies with JIS C 6560 standard. The product includes a straight version of 2-pole/mono Klinkensteckereinsatz with ABS body and CuZn/steel contacts. The product has a temperature range of -20°C to +70°C, a rated current of 2A, and a rated voltage of 34V.

LAN CAT.5e cables from LAPP KABEL for 'Structured Cabling Systems' meet the requirements acc. to EIA/TIA-568 and TSB36 as well as ISO/IEC 11801 resp. EN 50173 (class d). Used mainly where the terminal density is very high, e.g. cabling of offices, administration and R & D buildings in the tertiary area (horizontal). Please note: According to Standard ISO/IEC 11801 resp. EN 50173 the cable length in the Tertiary Area (Horizontal Area, Floor) should not exceed 100m (90m in the cable duct and 10m in the Working Area). These UTP cables are specified up to 200 MHz. Impedance of cables = 100 Ohm +/-15% EIA = Electronic Industries Association TIA = Telecommunication Industries Association TSB = Technical Systems Bulletin

PC 4 HV/ 7-ST-7,62 is a connector product of PHOENIX CONTACT company, with rated current of 20A, rated voltage of 800V, thread of M3, tightening torque of 0.5-0.6Nm, insulating material group of I, rated surge voltage of 8kV, rated voltage of 1000V.

This document is about the product MSTBV 2,5/ 8-GF-5,08 from PHOENIX CONTACT GmbH & Co. KG. The product is a 10-position connector with a nominal current of 12A, nominal voltage of 250V, pitch of 5.08mm, and green color. It can be assembled through soldering.