Industrial

S101S06V Series and S201S06V Series Solid State Relays (SSR) are an integration of an infrared emitting diode (IRED), a Phototriac Detector and a main output Triac. These devices are ideally suited for controlling high voltage AC loads with solid state reliability while providing 3.0kV isolation (Viso(rms)) from input to output.

This data sheet provides the technical specifications for the Pro-Elec SH10183R power lead.

The LT1512 is a 500kHz current mode switching regulator specially configured to create a constant-current/constant-voltage battery charger. It has a current sense feedback circuit for accurately controlling output current and supports flyback or SEPIC topology chargers. It allows charging even when the input voltage is lower than the battery voltage, has a maximum switch current of 1.5A, and 1% voltage accuracy for lithium battery applications.

The LTC1622 is a constant frequency current mode step-down DC/DC controller providing excellent AC and DC load and line regulation. The device incorporates an accurate undervoltage feature that shuts the LTC1622 down when the input voltage falls below 2V. The LTC1622 boasts a ±1.9% output voltage accuracy and consumes only 350µA of quiescent current. For applications where efficiency is a prime consideration and the load current varies from light to heavy, the LTC1622 can be configured for Burst Mode TM operation. Burst Mode operation enhances low current efficiency and extends battery run time. Burst Mode operation is inhibited during synchronization or when the SYNC/MODE pin is pulled low to reduce noise and possible RF interference. High constant operating frequency of 550kHz allows the use of a small inductor. The device can also be synchronized up to 750kHz for special applications. The high frequency operation and the available 8-lead MSOP package create a high performance solution in an extremely small amount of PCB area. To further maximize the life of the battery source, the P-channel MOSFET is turned on continuously in dropout (100% duty cycle). In shutdown, the device draws a mere 15µA.

This document is the datasheet of Pro-Elec SH10170R 2.00m SVT 18/3 Black power lead

The LTC3731H is a PolyPhase synchronous step-down switching regulator controller that drives all N-channel external power MOSFET stages in a phase-lockable fixed frequency architecture. It has features such as Burst Mode, OPTI-LOOP, and PolyPhase.

The G6RL PCB Relay is a low-profile power relay from Panasonic with a maximum switching current of 10A. It is only 12.3mm high, has a maximum switching capacity of 2,500 VA (NO), an electrical strength of 5 kV, and a clearance and creepage distance of 10 mm. It is suitable for a variety of electrical appliances, such as boilers, PLCs, I/O ports, timers, and temperature controllers.

The SILVYN® SP/SP-PU/FPS/FD-PU cable conduit system is a proven safety conduit system used to connect conduits and machines. It features a TPE sealing ring for a good seal and increased width across flats for safe transmission of forces.

This data sheet contains detailed information about three products: MM20247, MM20253 and MM20246. It includes product models, product functions, product features, product sizes, product images, etc.

HFA06TB120S is a state of the art ultra fast recovery diode from International Rectifier. Employing the latest in epitaxial construction and advanced processing techniques it features a superb combination of characteristics which result in performance which is unsurpassed by any rectifier previously available.

S102S02 Series and S202S02 Series Solid State Relays (SSR) are an integration of an infrared emitting diode (IRED), a Phototriac Detector and a main output Triac. These devices are ideally suited for controlling high voltage AC loads with solid state reliability while providing 4.0kV isolation (Viso(rms)) from input to output.

IS1016R IS1020R is a connector produced by Pro-Elec, with features including 2P + E plug, Approval Category IEC309-2, Colour Blue, IP Rating IP44, Current Rating 16, Voltage Rating 240, Number of Pins 3.

2U Energy Saving Lamps, available in 9W, 11W, 15W and 18W, with BC (B22), ES (E27) and SES (E14) bases, saving up to 80% energy and with a life span of up to 8000 hours