Industrial

The ISL95711 is a digitally controlled potentiometer (XDCP) with terminal voltage of ±3V or ±5V, 128 taps, and I2C serial interface. It consists of a resistor array, wiper switches, a control section, and nonvolatile memory.

The ISL6753 is a high-performance, low-pin-count alternative zero-voltage switching (ZVS) full-bridge PWM controller. Like the ISL6551, it achieves ZVS operation by driving the upper bridge FETs at a fixed 50% duty cycle while the lower bridge FETS are trailing-edge modulated with adjustable resonant switching delays. Compared to the more familiar phase-shifted control method, this algorithm offers equivalent efficiency and improved overcurrent and light- load performance with less complexity in a lower pin count package. This advanced BiCMOS design features low operating current, adjustable oscillator frequency up to 2MHz, adjustable soft-start, internal over temperature protection, precision deadtime and resonant delay control, and short propagation delays. Additionally, Multi-Pulse Suppression ensures alternating output pulses at low duty cycles where pulse skipping may occur.

Describes how to replace the ozone generator

The ISL60002 is a high precision, low power voltage reference from Intersil. It features Intersil's proprietary floating gate analog technology, low supply voltage operation and an ultra-low operating current of 400nA. Additional features include guaranteed initial accuracy as low as ±1.0mV, @ 20ppm/°C temperature coefficient and long-term stability of <<10ppm/√1kHrs.

This document is the user manual for Agilent UV Pass Filter (350B) Replacement Kit Accessory. It introduces the steps to replace the filter and O rings.

The ISL3990 is a dual-band power amplifier from ISL company. It operates in the ISM and U-NII bands with an output power of 21 dBm (typical). The power supply voltage is 2.7V to 3.6V and the power gain is 28 dB (typical). The working frequency range is 1.8GHz to 2.4GHz and 5.15GHz to 5.825GHz.

The IRU1206 family of devices are ultra low dropout 1A regulators using PNP transistor as the pass element. These products are ideal when a single input supply is only available and the dropout voltage is less than 1V, exceeding the minimum dropout characteristics of NPN/ PNP hybrid regulators. One common application of these regulators is where input is 3.3V and a 2.5V output is needed. Besides the low dropout of less than 0.5V, other features of the family of the parts are: micro-power shut- down capability and output UVLO detection where Flag pin is switched low when output is below 5% of its nominal point.

Agilent Feature Extraction Software (v9.5) Reference Guide

IRF3711ZPbF is a power MOSFET produced by IRF company. It is mainly used in high frequency synchronous buck converters. It has the characteristics of low RDS(on), ultra-low gate impedance, fully characterized avalanche voltage and current.

This manual describes the features and use of Agilent Feature Extraction Software.

This is the Agilent 6890N Gas Chromatograph Troubleshooting Manual

This document is an instruction manual for Agilent Micro Fluidics 1/16-inch Tube Union Kits.

Introduced the Site Preparation Guide for Agilent Technologies 5975 Series Mass Selective Detectors

This document is a guide for installing the Thermal Conductivity Detector on a 6850 GC Accessory G2623A 2 from Agilent Technologies, Inc. It provides safety information and operating instructions.

This document provides instructions on how to prepare the Electronic Pressure Control (EPC) module for later installation into the Agilent 6850 Gas Chromatograph (GC), prepare the µECD Signal board for later installation, and perform the actual Accessory installation into the GC. Part 1 involves the preparation of the µECD EPC module, which includes installing the front and back covers and other components. Part 2 involves the preparation of the µECD Signal board, specifically for installing the Microcell Electron Agilent 6850 Series II Network GC System Capture Detector Accessory G3347B. Part 3 involves the actual installation of the Accessory into the GC, following specific tools and procedures.