Industrial

This document describes the application of HDSL interface xDSL transformers, matched to Booktree IC BT 8960. It has a data transfer rate of 288 kB/s and is available in SMD version upon request. The marking includes the manufacturer, middle block of ordering code, and date code. It is packed in a polyfoam tray with a packing unit of 500 pcs. The technical data includes ordering code, type/core, inductance, and other electrical specifications.

This document describes the application of PTC thermistors for overcurrent protection in telecom equipment, including compliance with ITU-T K20, K21, K45 standards.

This application note describes a rapid method for the simultaneous detection and quantification of 37 acylcarnitines and 12 amino acids in dried blood spots using the Agilent Triple Quadrupole LC/MS System in neutral loss scan, precursor ion scan and multiple reaction monitoring (MRM) data acquisition modes. With a run time of 1.6 minutes, the assay provides the ability to analyze 400-500 samples per day, and custom reports provide all the information needed to rapidly list the critical elements for the analysis.

This Application Note describes the design and performance of an HPLC-Chip with a hybrid TiO2 and C18 enrichment column for selective phosphopeptide enrichment and analysis.

This application note outlines a viable method for reliably detecting low-fem- togram levels of perfluorinated carboxylates (PFCA) and sulphonates (PFSA) without background component interference, with an inline contaminant trap LC modification. Good chromatographic resolution of all perfluorinated compounds was observed. A representative suite of PFCAs and PFSAs were analyzed herein and were all detected at on-column levels lower than 75 fg in drinking water matrices (S/N >3.) The most sensitive analytes PFHxS, PFDS and PFBS were detected at 2.6, 3.2 and 5 fg levels, respectively. Method detection limits for spiked pork liver matrix extract samples were below 600 fg on-column for the entire analyte suite. No detectable background conta- mination was observed in blank injections for any analyte in this study. Linearity for up to five orders of magnitude with R2 values above 0.996 for the entire suite were recorded.

This document describes a 20 Amp subminiature PCB power relay for automotive use. The relay features low cost, low profile, high operating temperature, SPST and SPDT contacts.

The document introduces a high-performance and low-power AVR 8-bit RISC architecture product. It features 118 powerful instructions, most of which can be executed in a single cycle. It has 32 general-purpose working registers and can achieve up to 8 MIPS throughput at a clock frequency of 8 MHz. The product also includes 2K/4K bytes of in-system programmable flash, 128 bytes of SRAM, and 128/256 bytes of in-system programmable EEPROM. It also includes a 8-bit timer/counter, an expanded 16-bit timer/counter, an on-chip analog comparator, a programmable watchdog timer, and a programmable UART.

AT24C512SC is a serial electrically erasable and programmable read-only memory (EEPROM) with the features of low power and low voltage operation. It provides 524,288 bits of storage space organized into 65,536 words of 8 bits each. This device is suitable for smart card applications, with high reliability and compatibility.

This document introduces a new frequency modulator for reducing EMI. It can generate a low EMI clock from crystal, ceramic resonator or system clock, which can reduce the EMI of downstream clock and data dependent signals in the system.

ASD07H series is 7 watt open frame DC/DC converter with 4:1 input range, high efficiency, regulated outputs, 1500V isolation and integral finned heatsink, approved by EN60950 and UL60950-1.

The AS6WA25616 is a 3.0V to 3.6V 256K×16 Intelliwatt™ low-power CMOS SRAM with one chip enable. It features industrial and commercial temperature ranges available, 262,144 words × 16 bits organization, 3.0V to 3.6V at 55 ns, low power consumption, 1.5V data retention, equal access and cycle times, easy memory expansion with CS, OE inputs, smallest footprint packages - 48-ball FBGA - 400-mil 44-pin TSOP 2, ESD protection ≥ 2000 volts and latch-up current ≥ 200 mA.

APL1431 is a 3-terminal adjustable voltage reference product produced by ANPEC company. It has good thermal stability and an output voltage range of 2.5V-20V. The typical output impedance is 0.1 ohms.

The AP1601 is a high efficiency step-up DC/DC converter from Anachip Corp. It can be used with 1 to 4 NiMH battery cells and only requires three external components to deliver a fixed output voltage of 3.3V or 5V. The AP1601 starts up from less than 0.9V input with 1mA load. The Pulse Frequency Modulation scheme provides optimized performance for applications with light output loading and low input voltages. The output ripple and noise are lower compared with the circuits operating in PSM mode. The PFM control circuit operating in 100KHz (max.) switching rate results in smaller passive components. The space saving MSOP packages make the AP1601 an ideal choice of DC/DC converter for space conscious applications, like pagers, electronic cameras, and wireless microphones.

The AN7158N is an integrated circuit designed for a power amplifier with a 7.5W (16V, 4Ω) output, low noise, and low distortion. It is suitable for TV sets with multi-sound. The chip incorporates two amplifiers, enabling stereo operation. The 12-pin SIL package allows for compact and high-density mounting.