Industrial

The CBT6820 is a 20-bit bus switch with precharged outputs and Schottky undershoot protection for live insertion. It features TTL compatible inputs and outputs, a 5Ω switch connection between port A and port B, and thin shrink small outline (TSSOP). Undershoot protection is included to prevent shoot through level changes, and the device precharges the B port to a user-selectable bias voltage (BIASV) to minimize signal distortion during live insertion. It is organized as two 10-bit switches with individual enable (OE) input. When OE is low, the switch is on and port A is connected to port B. When OE is high, the switch between port A and port B is open and the B port is precharged to BIASV through the equivalent of a 10-kΩ resistor. Special clamp circuitry and Schottky diode clamps to ground are used to prevent an under voltage on the A side (Vin < GND) from causing the B side precharge voltage to drop below the ‘‘1” state.

The CBT6810 is a 10-bit bus switch with precharged outputs and Schottky undershoot protection for live insertion from Philips Semiconductors. The features of this switch include a 5-ohm switch connection between port A and port B, TTL-compatible input and output levels, undershoot protection to prevent shoot-through level changes, and bias voltage pre-charging the outputs to minimize signal distortion during live insertion.

This product is a 10-bit bus switch with precharged outputs for live insertion

The CBT3857 is a 10-bit bus switch with 10 kOhm pull-down termination resistors. This switch is designed for 3 V to 3.6 V VCC operation and SSTL_2 output enable (OE) input levels. When OE is low, the switch is on and port A is connected to port B. When OE is high, the switch is open, and a high-impedance state exists between the two ports. The switch's low on-state resistance allows connections to be made with minimal propagation delay. The CBT3857 is characterized for operation from 0°C to +85°C.

CBT3384 is a 10-bit high-speed TTL-compatible bus switch from PHILIPS. It has a 5-ohm switch connection and TTL-compatible control inputs and output levels.

The CBT3306 is a dual bus switch produced by Philips, which has features such as 5Ω switch connection, TTL-compatible input levels, plastic small outline (SO) and thin shrink small outline (TSSOP) package options, over 100mA latch-up protection and over 2000V HBM ESD protection.

The SN74CBT3306 is a dual FET bus switch device manufactured by Texas Instruments. It features independent line switches. Each switch is disabled when the associated output-enable (OE) input is high. The SN74CBT3306 is characterized for operation from -40°C to 85°C.

The CBT3257 is a quad 1-of-2 high-speed TTL-compatible multiplexer/demultiplexer

This datasheet details the CBT3253 dual 1-of-4 high-speed TTL-compatible FET multiplexer/demultiplexer's features, including 5 Ω switch connection, TTL-compatible input levels, minimal propagation delay, ESD protection, and latch-up testing

The CBT3251 is a 1-of-8 high-speed TTL-compatible FET multiplexer/demultiplexer. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise.

CBT3245A is a 8-bit high-speed TTL-compatible bus switch produced by Philips

The CBT3245 is an octal bus switch with output enable, providing eight bits of high-speed TTL-compatible bus switching. It is functionally equivalent to the QS3245 and has a standard '245-type pinout. The switch has a low on-state resistance, allowing for minimal propagation delay in connections. The CBT3245 is organized as one 8-bit switch. When the enable signal OE is low, the switch is on and connects port A to port B. When OE is high, the switch is open and a high-impedance state exists between the two ports. The CBT3245 operates in a temperature range of -40°C to 85°C.

This document describes an eMethod for waterborne volatile organic compounds analysis based on the Agilent 5975 inert mass spectrometer.

CBT3244A is an octal bus switch with quad output enables. It features a standard '244-type pinout, a 5 Ω switch connection between two ports, TTL compatible control input levels. The package options include plastic small outline (D), shrink small outline (DB), QSOP (DS), and thin shrink small outline (TSSOP). It has latch-up protection exceeding 500 mA per JESD78 and ESD protection exceeding 1000 V HBM per JESD22-A114, 200 V MM per JESD22-A115, and 1000 V CDM per JESD22-C101. The CBT3244A provides eight bits of high-speed TTL-compatible bus switching in a standard '244 device pinout. The low on-state resistance of the switch allows connections to be made with minimal propagation delay. The CBT3244A device is organized as two 4-bit low-impedance switches with separate output-enable (OE) inputs. When OE is LOW, the switch is on and data can flow from port A to port B, or vice versa. When OE is HIGH, the switch is open and high-impedance state exists between the two ports. The CBT3244A is characterized for operation from –40 °C to 85 °C.

The CBT3244 is an eight-bit high-speed TTL-compatible bus switch that provides standard '244 device pinout, 5Ω switch connection between two ports, TTL compatible control input levels.