Industrial

The MM74C08 is a quad 2-input AND gate that uses complementary MOS (CMOS) transistors to achieve a wide power supply operating range, low power consumption, and high noise margin. These gates provide the basic functions required in digital integrated circuit systems. The N- and P-channel enhancement mode transistors provide a symmetrical circuit with output swing essentially equal to the supply voltage. No DC power other than that caused by leakage current is consumed during static condition. All inputs are protected from damage due to static discharge by diode clamps to VCC and GND.

The MM54C08/MM74C08 is a quad 2-input AND gate from National Semiconductor. The circuit uses complementary MOS (CMOS) transistors to achieve wide power supply operating range, low power consumption and high noise margin. It can be used in the design of digital integrated circuit systems.

This datasheet provides information about MM74C165's features, pin assignments, and package.

The MM70C95, MM80C95, MM70C97, and MM80C97 are monolithic complementary MOS (CMOS) integrated circuits constructed with N- and P-channel enhancement mode transistors. They convert CMOS or TTL outputs to TRI-STATE outputs with no logic inversion and provide the logical opposite of the input signal. The MM70C95 and MM80C95 and the MM70C96 and MM80C96 have common TRI-STATE controls for all six devices. The MM70C97 and MM80C97 and the MM70C98 and MM80C98 have two TRI-STATE controls, one for two devices and one for the other four devices. Inputs are protected from damage due to static discharge by diode clamps to VCC and GND. These gates have a wide supply voltage range (3.0V to 15V), guaranteed noise margin (1.0V), high noise immunity (0.45 VCC (typ.)), and TTL compatibility. They can drive 1 TTL load and are used in bus drivers. The typical propagation delay into a 150 pF load is 40 ns.

The TS27M4C,I,M is a low cost, low power quad operational amplifier from SGS-THOMSON. It is designed to operate with single or dual supplies and has an excellent consumption-speed ratio. This series is ideally suited for low consumption applications.

TS27M2 is a low power dual operational amplifier from ST company. It offers very high input impedance and extremely low input currents. It is ideal for low power applications. Three power consumptions are available: 10µA/amp, 150µA/amp and 1mA/amp, to always have the best consumption-speed ratio.

This document introduces a low power dual operational amplifier with features such as low power consumption, output voltage swing to ground, excellent phase margin on capacitive loads, stable and low offset voltage.

The data sheet introduces the STEVAL-ISA056V1 6 rows - 30 mA LEDs driver with boost converter for LCD panels backlight evaluation board, which is composed of the PM6600 controller, with a 4.5V to 28V input voltage range, internal Power MOSFET, internal +5V LDO for device supply, up to 36V output voltage, constant frequency peak current-mode control, 200kHz to 1MHz adjustable switching frequency, external synchronization for multi-device applications, pulse-skip power saving mode at light load, programmable soft-start, programmable OVP protection, single ceramic output capacitor, latched thermal shutdown.

This document describes a low power quad operational amplifier with features such as low power consumption, output voltage swing to ground, excellent phase margin on capacitive loads, stable and low offset voltage.

This document describes the features and characteristics of a metal body proximity detector based on the TDE0160.

This document introduces STEVAL-IFS005V1, a metal body proximity detector based on the TDA0161, which features a 10 mA output current, a supply voltage of +4 V to +35 V, and a 10 MHz oscillator frequency

STEVAL-ISS001V1 is a line interactive 450 W UPS reference design in a 120 V / 60 Hz model.

This document provides detailed information about STEVAL-ISS001V2 Line interactive 450 W UPS reference design, including features, specifications and more.

This data brief introduces the STEVAL-ISA052V2 evaluation board features, including input voltage range, reference voltage, output voltage, load transient response, current sensing, overvoltage protection, undervoltage protection, thermal shutdown, soft-start, pulse-skip mode, ceramic output capacitors application support, output voltage ripple compensation and output soft-end

This data brief introduces the STEVAL-ILL014V1 evaluation board for the STCS1 constant current controller for high brightness LEDs.