MOTOROLA Manuals

This data sheet provides detailed parameters of the MPS4250 model, including maximum rated voltage, maximum rated current, total device power dissipation, operating temperature range, thermal resistance, etc.

This is a datasheet for a transistor

This document is about the datasheet of MPS4124/D, which introduces the features and characteristics of the product, including maximum ratings, thermal characteristics, electrical characteristics, etc.

MJW21191 and MJW21192 are bipolar power transistors manufactured by Motorola, specifically designed for power audio output or high power drivers in audio amplifiers.

MJW16212 is a state-of-the-art SWITCHMODE bipolar power transistor. It has 1500 V collector-emitter breakdown capability, typical dynamic desaturation specified (new turn-off characteristic), application-specific state-of-the-art die design, fast switching (200 ns inductive fall time and 2000 ns inductive storage time), low saturation voltage (0.15 V at 5.5 A collector current and 2.5 A base drive), low collector-emitter leakage current (250 µA max at 1500 V VCES), high emitter-base breakdown capability (8.0 V min, for high voltage off drive circuits)

This is a technical datasheet for MJF16206 and MJW16206

MJ16110/MJW16110 is a bipolar power transistor launched by Motorola. Its maximum collector-emitter sustaining voltage is 400V, and its maximum collector-emitter breakdown voltage is 650V. This transistor is specially designed for half-bridge and full-bridge offline converters, and has good dynamic saturation characteristics and rugged RBSOA capability.

This data sheet provides the maximum ratings for the 1.5 kV SWITCHMODE series bipolar power transistors, including collector-emitter voltage, collector-emitter saturation voltage, emitter-base voltage, emitter-base saturation current, collector current, and emitter current.

This datasheet provides parameters of 1kV SWITCHMODE series bipolar power transistors, including reverse-biased SOA, switching times with inductive loads, saturation voltages, leakage currents, etc.

These transistors are designed for high-voltage, high-speed, power switching in inductive circuits where fall time is critical. They are particularly suited for line-operated switchmode applications. The MJ16012 and MJW16012 are selected high gain versions of the MJ16010 and MJW16010 for applications where drive current is limited. • Switching Regulators • Fast Turn-Off Times – TC = 100°C • Inverters 50 ns Inductive Fall Time (Typ) • Solenoids 90 ns Inductive Crossover Time (Typ) • Relay Drivers 800 ns Inductive Storage Time (Typ) • Motor Controls • 100�C Performance Specified for: • Deflection Circuits Reverse-Biased SOA with Inductive Loads Switching Times with Inductive Loads Saturation Voltages Leakage Currents

The MC10E404/100E404 is a 4-bit differential AND/NAND device. The differential operation of the device makes it ideal for pulse shaping applications where duty cycle skew is critical. Special design techniques were incorporated to minimize the skew between the upper and lower level gate inputs. Because a negative 2-input NAND function is equivalent to a 2-input OR function, the differential inputs and outputs of the device also allow for its use as a fully differential 2 input OR/NOR function. The output RISE/FALL times of this device are significantly faster than most other standard ECLinPS devices resulting in an increased bandwidth. The differential inputs have clamp structures which will force the Q output of a gate in an open input condition to go to a LOW state. Thus, inputs of unused gates can be left open and will not affect the operation of the rest of the device. Note that the input clamp will take affect only if both inputs fall 2.5V below VCC.

MC10E/100E337 is a 3-bit registered bus transceiver with scan.

The MC10E/MC100E336 is an integrated circuit that contains three bus transceivers with both transmit and receive registers.

The MC100LVE310 is a low voltage, low skew 2:8 differential ECL fanout buffer designed with clock distribution in mind. The device features fully differential clock paths to minimize both device and system skew. The LVE310 offers two selectable clock inputs to allow for redundant or test clocks to be incorporated into the system clock trees. The MC100E310 is pin compatible to the National 100310 device. The MC100LVE310 works from a –3.3V supply while the MC100E310 provides identical function and performance from a standard –4.5V 100E voltage supply.