Philips manuals, page 68
philips SAA2003 Stereo filter codec handbook
SAA2003 is a single chip stereo filter and codec from Philips Semiconductors. It features a wide operating voltage range (2.7-5.5 V), low power consumption (98 mW, 3.0 V), sleep mode to reduce power consumption and electromagnetic interference (EMI), transparent serial audio data mode in sleep mode and IEC 958 digital output.
philips SAA1575HL Global Positioning System (GPS) baseband processor handbook
The SAA1575HL is a Global Positioning System (GPS) baseband processor with various functions and features.
philips SAA1504T Safety IC handbook
SAA1504T is a protection circuit for single cell Li-ion battery packs. It features zero voltage start-up, overcharge protection, overdischarge protection and temperature protection.
philips SAA1502ATS Safety IC for Li-ion handbook
The SAA1502ATS is a safety IC launched by Philips. This IC has temperature protection, zero voltage start-up, over-charge and over-discharge protection, etc. It is suitable for single cell lithium-ion battery packs and is currently widely used in GSM and other portable telephone batteries.
philips SAA1501T Battery charge level indicator handbook
The SAA1501T is a battery monitor and charge current control circuit for rechargeable battery systems. It features high integration, accurate charge and discharge measurements, large dynamic range of charge and discharge currents, and independent settings of charge and discharge efficiency.
philips SAA1310 Control interface for VHS video recorders handbook
This document is a specification sheet for Philips SAA1310 control interface chip, which provides information such as the chip's functions, pin definitions, and package forms.
philips SAA1305T On/off logic IC handbook
SAA1305T is an on/off logic IC intended for use in car radios to interface between a microcontroller and various input signals such as ignition, low supply detection, on/off key and external control signals.
philips SAA1300 Tuner switching circuit handbook
This document is about SAA1300, SAA1300 is a switch circuit that is used to turn on and off the power lines of various circuit parts via an I2C bus signal. It can also be used to supply current for switching diodes in radio and television tuners. It contains 5 output stages, which are capable of supplying up to 85 mA in the ON state or sinking up to −100 µA in the OFF state. Current limiting and short-circuit protection are included. The output stages are driven by a shift register/latch combination which is loaded via data from the I2C bus. A power-on reset of the latches ensures the OFF state of the output stages (OUT 2 to OUT 5) without data reception from the I2C bus. A subaddressing system allows the connection of up to three circuits on the same I2C bus lines; one of the outputs (OUT 1, pin 7) can also be used as an input to select the device via a simple internal A/D converter.
philips SAA1101 Universal sync generator (USG) handbook
The SAA1101 is a Universal Sync Generator (USG) from Philips and is designed for use in video sources such as cameras, film scanners, video generators and associated apparatus. The circuit can be considered as a successor to the SAA1043 sync generator and the SAA1044 subcarrier coupling IC.
Philips TJA1054A Fault-tolerant CAN transceiver handbook
TJ1054A is a fault-tolerant CAN transceiver, which is used in automotive bus communication. It supports up to 32 nodes with a maximum transmission speed of 125kBaud.
Philips TJA1054 Fault-tolerant CAN transceiver handbook
This document describes the features of TJA1054 fault-tolerant CAN transceiver, including optimized for in-car low-speed communication, support for multiple node connections, support for unshielded bus wires, very low Radio Frequency Interference (RFI), fully integrated receiver filters, bus failure management, protection features, and support for low power modes.
Philips TJA1050 High speed CAN transceiver handbook
This document describes the features and characteristics of the TJA1050 high speed CAN transceiver, including full compatibility with the ISO 11898 standard, high speed transmission rate, transmit data dominant time-out function, transient protection in automotive environment, silent mode, differential receiver with wide common-mode range for high electromagnetic immunity, input levels compatible with 3.3V devices, thermal protection, short-circuit proof to battery and ground, and non-disturbance of bus lines by unpowered nodes.
Philips TJA1053 Fault-tolerant CAN transceiver handbook
TJ1053 is a CAN bus controller interface chip launched by Philips Semiconductors. It is mainly used for low-speed automotive bus communication applications, which can support up to 125kbps baud rate and connect up to 32 nodes.
Philips TJA1040 High speed CAN transceiver handbook
TJA1040 is a high speed CAN transceiver for automotive applications, with high speed (up to 1 MBaud), very low standby current and remote wake-up capability via the bus.
Philips TJA1020 LIN transceiver handbook
The TJA1020 LIN transceiver is a low power, high performance interface for Local Interconnect Network (LIN). It supports baud rates up to 20 kbit/s. The device includes an integrated termination resistor for connection from either 3.3 V or 5 V devices. The TJA1020 also features a low slope mode for further reduction of EME.