STMicroelectronics manuals, page 233
ST STEVAL-ISB005V1 handbook
This is a low-cost Li-Ion battery charger demonstration board based on the ST7263BK6 and L6924D. It can be used both in USB mode and adapter mode.
ST STEVAL-IHI002V1 handbook
This data sheet introduces the STEVAL-IHI002V1, a daughter board based on the STMPE1208S 12-bit GPIO expander with an additional 12-channel capacitive sensing sensor, which is able to interface a main MCU through I²C bus. The daughter board is designed to work as a daughter board for the main board (e.g. STEVAL-IHI001V1) for home appliance user interface.
ST STEVAL-ISA031V1 handbook
This is a data brief about STMicroelectronics' demonstration board for a 40W auxiliary 3-phase power supply based on the L6565 and STW4N150. It features an input voltage range of 185V to 460V, input frequency range of 50/60Hz, output voltage of 24V @ 1.7A and 5V @ 1A, and a total output power of 40W. The board utilizes a high voltage MOSFET (1500V breakdown voltage) to optimize the operation of the quasi-resonant flyback converter based on the primary controller L6565. It is designed for low power applications and has two outputs, 24V and 5V, capable of delivering more than 40W.
ST STEVAL-IPE005V1 handbook
The STEVAL-IPE005V1 is a demonstration programmer board based on the STPM01 energy meter. It is fully compatible with the STPM01 energy meter and the appropriate manager software. It is an integrated system designed to provide a complete, ready-to-use energy meter application. The board is a high-end solution for power metering based on the STR710 microcontroller with an embedded RTC and an external memory interface (EMI) capable of driving 1 Mbyte of on-board SRAM. The demonstration board also integrates an on-board optical insulated serial line, allowing isolation of the board ground reference.
ST STEVAL-IPE008V1 handbook
STEVAL-IPE008V1 is an energy meter (3-phase) demonstration board based on the STPM01 and STR715FR0. It features a multi-chip topology, in which each phase is monitored using a single-phase device, a common clock network, and a power supply in fly-back topology using a VIPer12ADIP-E.
ST STEVAL-IHI001V1 handbook
STEVAL-IHI001V1 is a demonstration board designed to simulate the user interface of a modern washing machine.
ST STEVAL-ISB006V1 handbook
This data brief describes the features of the STEVAL-ISB006V1 dual USB/wall adapter Li-Ion battery charger with gas gauge demonstration board based on the STw4102.
ST STEVAL-IFS006V1 handbook
The STEVAL-IFS006V1 is a smart inductive proximity switch demonstration board based on the Ultralite 8-bit microcontroller and the TDE1708DFT. It features high flexibility, sensitivity and hysteresis adjustment, in-circuit programming and debugging capabilities, analog and digital temperature compensation, PNP and NPN sensor functionality configurations, indicator status LED, overload and short-circuit protection, GND and VS open wire protection, and compact design.
ST STEVAL-IFP008V1 handbook
This datasheet introduces the STMicroelectronics CLT3-4B logic input termination product features, characteristics, and usage instructions.
ST STEVAL-CCA007V1 handbook
The STEVAL-CCA007V1 demonstration board is designed to test the features and performance of the TS2012, a fully differential class D stereo power amplifier. The board has various features, including a wide operating range, high output power, and low power consumption.
ST STEVAL-IHT003V1 handbook
The e-STARTER demonstration board is an innovative solution by STMicroelectronics to reduce power losses caused by positive temperature coefficient (PTC) resistors in compressor starter circuits.
ST STEVAL-CLP001V1 handbook(1)
This demonstration board is based on the STOD2540 and is dedicated to passive matrix OLED (PMOLED) displays for portable handsets and provides the pre-charge and biasing voltage of the column matrix driver. The STOD2540 is a boost converter that operates from 3.0V to 5.5V and can provide an output voltage as high as 25V. The current capability of the STOD2540 allows the supply of a 1", 1.3" or 1.5" color PMOLED. The maximum output current capability is 40mA with an output voltage up to 25V, while the supply voltage is from 3.0V to 5.5V.
ST STEVAL-PCC003V1 handbook(1)
This document describes the hardware and software features of the low-speed USB demonstration board based on the STUSB03 transceiver and ST7263BE2 microcontroller. The board is ideal for use in mobile phones, digital cameras, printers, PDAs, etc.
ST STEVAL-PCC004V1 handbook
This document introduces the STEVAL-PCC004V1 low-speed USB demonstration board, which is based on the STUSB02E transceiver and ST7263BE2 microcontroller. It supports both USB full-speed and USB low-speed operations and is suitable for mobile phones, digital cameras, printers, PDAs, etc.
ST STEVAL-IHM015V1 handbook
The STEVAL-IHM015V1 is a low voltage motor control demonstration kit based on the ST7MC2S4 and STS8DNH3LL.