STMicroelectronics Manuals

This document describes a 20W dimmable CFL (compact fluorescent lamp) ballast solution that can completely replace incandescent lamps in dimming systems. The dimming range of this solution is from below 20% up to 100% of full light output without changing the triac dimmer. Compared to traditional CFL designs, this dimmable solution not only provides energy savings but also higher reliability and longer operating life.

This document is a data brief that introduces the features and functions of the STEVAL-CBP005V1 front panel demonstration board, including 16 x 3 mm blue LEDs for status and function indication, 2 x 5 mm BiColor LEDs, 12 front panel function keys, 1 reset button on rear, 11-pin connector termination for easy interface to host, all data and power lines and additional signals available on connector.

This document describes a 55W flyback SMPS demonstration board for an alarm system, based on L5991 and STP12NK80Z. It features multiple output voltages and signals, as well as a battery charger circuit. The input voltage range is 88-300Vac, and the output voltages include 13.8V, 25V, and 3.8V.

STEVAL-TDR005V1 is a RF broadband power amplifier intended for linear or nonlinear operation over the band 1.8 to 54 MHz using 2x SD2943 gold metallized N-channel MOS field- effect transistors.

The STEVAL-TDR007V1 is a 200W RF power amplifier from ST company. It works at 1030MHz with a supply voltage of 36V. The maximum output power is 200W, the input power is 23dBm, the harmonics are <-45dBc and the rise and fall time are <100ns.

The STEVAL-ISA032V1 is a 60 W forward converter demonstration board for fiscal cash register based on the L5991 and STP10NK60Z.

The STEVAL-ISA020V1 is a 3.5W battery charger demonstration board based on VIPer12AS-E and TSM101. It features an input voltage range of 88-264VAC, output voltage range of 0-7V, and output current of 0.5A.

The TS27M4C,I,M is a low cost, low power quad operational amplifier from SGS-THOMSON. It is designed to operate with single or dual supplies and has an excellent consumption-speed ratio. This series is ideally suited for low consumption applications.

TS27M2 is a low power dual operational amplifier from ST company. It offers very high input impedance and extremely low input currents. It is ideal for low power applications. Three power consumptions are available: 10µA/amp, 150µA/amp and 1mA/amp, to always have the best consumption-speed ratio.

This document introduces a low power dual operational amplifier with features such as low power consumption, output voltage swing to ground, excellent phase margin on capacitive loads, stable and low offset voltage.

The data sheet introduces the STEVAL-ISA056V1 6 rows - 30 mA LEDs driver with boost converter for LCD panels backlight evaluation board, which is composed of the PM6600 controller, with a 4.5V to 28V input voltage range, internal Power MOSFET, internal +5V LDO for device supply, up to 36V output voltage, constant frequency peak current-mode control, 200kHz to 1MHz adjustable switching frequency, external synchronization for multi-device applications, pulse-skip power saving mode at light load, programmable soft-start, programmable OVP protection, single ceramic output capacitor, latched thermal shutdown.

This document describes a low power quad operational amplifier with features such as low power consumption, output voltage swing to ground, excellent phase margin on capacitive loads, stable and low offset voltage.

This document describes the features and characteristics of a metal body proximity detector based on the TDE0160.

This document introduces STEVAL-IFS005V1, a metal body proximity detector based on the TDA0161, which features a 10 mA output current, a supply voltage of +4 V to +35 V, and a 10 MHz oscillator frequency

STEVAL-ISS001V1 is a line interactive 450 W UPS reference design in a 120 V / 60 Hz model.