VQN5050K-E is a quad channel high side driver for automotive applications by ST. It has features such as low power consumption, 3.0 V CMOS compatible input, optimized electromagnetic emission and low electromagnetic susceptibility.
The VNQ830P-E is a quad channel high-side driver with features including very low standby current, CMOS compatible input, thermal shutdown protection and diagnosis, undervoltage shutdown, overvoltage clamp, output stuck to VCC detection, load current limitation, reverse battery protection, and electrostatic discharge protection.
This document introduces the features of VND810PEP-E, including CMOS compatible inputs, open drain status outputs, open-load detection, undervoltage and overvoltage shutdown, loss of ground protection, very low standby current, reverse battery protection.
The VNH3ASP30-E is a full-bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high-side driver (HSD) and two low- side switches. The HSD switch is designed using STMicroelectronics proprietary VIPower™ M0 technology that efficiently integrates a true Power MOSFET with an intelligent signal/protection circuit on the same die. The low-side switches are vertical MOSFETs manufactured using STMicroelectronics proprietary EHD (“STripFET™”) process.
The VNH2SP30-E is a full bridge motor driver intended for a wide range of automotive applications. It features 5V logic level compatible inputs, undervoltage and overvoltage shut-down, overvoltage clamp, thermal shut down, cross-conduction protection, linear current limiter, very low stand-by power consumption, PWM operation up to 20 kHz, protection against loss of ground and loss of VCC, and current sense output proportional to motor current.
The VND830PEP-E is a monolithic device designed in STMicroelectronics VIPower™ M0-3 Technology, intended for driving any kind of load with one side connected to ground.
This document is VN920DSP datasheet, introduce the characteristics of this product, including CMOS compatible input, on state open load detection, off state open load detection, short circuit load protection, undervoltage and overvoltage shutdown, protection against loss of ground, very low standby current and reverse battery protection
The VN920D-B5 / VN920DSO is a high-side driver from STMicroelectronics with CMOS-compatible input, on-state open load detection, off-state open load detection, shorted load protection, under-voltage and over-voltage shutdown, protection against loss of ground, very low standby current and reverse battery protection.
VN770K is a quad smart power solid state relay for complete H-bridge configurations, featuring linear current limitation, very low standby power dissipation, short circuit protection, status flag diagnostic (open drain), integrated clamping circuits, undervoltage protection and ESD protection.
The L9950 and L9950XP are microcontroller driven multifunctional door actuator driver for automotive applications. Up to five DC motors and five grounded resistive loads can be driven with six half bridges and five highside drivers. The integrated standard serial peripheral interface (SPI) controls all operation modes (forward, reverse, brake and high impedance). All diagnostic informations are available via SPI.
L9337MD is a triple low side driver with an input voltage range of -24V to +45V, a operating voltage range of 4.5V to 32V, output overcurrent limiting, low EMI, over-temperature protection, open output and other features.
The L4979D and L4979MD are low dropout linear regulators with microprocessor control functions such as low voltage reset, watchdog, on/off control. Typical quiescent current is 100µA in very low output current mode and enabled regulator. The devices drop to 6µA with not enabled regulators. On chip trimming results in high output voltage accuracy (2%). Accuracy is kept over wide temperature range, line and load variation. The maximum input voltage is 40 V. The max output current is internally limited. Internal temperature protection disables the voltage regulator output.
TDA7376PD is a new technology dual bridge audio amplifier designed for car radio applications. It features high output power capability, minimum external components count, differential inputs, mute function, etc.
