STMicroelectronics manuals, page 158
ST L6386AD handbook
L6386AD is a high voltage driver from ST company. It can drive power MOS or IGBT with up to 600V voltage rail.
ST STUSBCD01B handbook
The STUSBCD01B is a USB charger detection IC from ST company, which can detect dedicated USB chargers, Host/Hub chargers or standard host ports connected to the USB DP/DM data lines. The device implements two different detection methods in order to be able to distinguish between a dedicated charger and a Host/Hub charger. Operation is controlled through three general purpose I/O pins; a hardware open drain detection output is also available. An internal regulator provides the 1.8 V supply voltage for the internal blocks and state machine while a clamping device prevents VBUS voltage from going over 6 V (typ.). The STUSBCD01B is available in a 12 bumps Flip-Chip 0.4 mm pitch package.
ST VNI2140J handbook
VNI2140J is a monolithic device designed using STMicroelectronics' VIPower technology. The device drives two independent resistive or inductive loads with one side connected to ground. Active current limitation prevents a drop in system power supply in cases of shorted-load, and built-in thermal shutdown protects the chip from damage due to over-temperature and short-circuit. In overload conditions, channel turns OFF and ON automatically to maintain the junction temperature between TTSD and TR. If the case temperature reaches TCSD, the overloaded channel is turned OFF and restarts only when case temperature decreases down to TCR. In order to avoid high-peak current from the supply, when more than one channel is overloaded the TCSD restart is not simultaneous. Non overloaded channels continue to operate normally. The open-drain diagnostic outputs are used to detect overload and turn-off status.
ST VNI8200XP handbook
The VNI8200XP is an octal high-side smart power solid state relay with serial/parallel selectable interface on chip. It features 0.7 A output current, short-circuit protection, 8-bit and 16-bit SPI interface, channel overtemperature detection and protection, thermal independence of separate channels, drives all types of loads (resistive, capacitive, inductive load), GND loss protection, Power Good diagnostic, undervoltage shutdown with hysteresis, overvoltage protection (VCC clamping), very low supply current, common fault open drain output, IC warning temperature detection, channels output enable, 100 mA high efficiency step-down switching regulator with integrated boot diode, adjustable regulator output, switching regulator disable, 5 V and 3.3 V compatible I/Os, channel outputs status LED driving 4 x 2 multiplexed array, fast demagnetization of inductive loads, ESD protection.
ST STUSB06E handbook
The STUSB06E is a single chip USB transceiver that complies with the USB v2.0 standard. It supports full-speed (12 Mbps) and low-speed (1.5 Mbps) operation, has low power consumption, supports charger detection, and supports sharing mode.
ST STPMC1 handbook
This product is a programmable poly-phase energy calculator IC that supports 1-, 2- or 3-phase WYE and Delta services, from 2 to 4 wires, computes cumulative active and reactive wide-band and fundamental harmonic energies, computes active and reactive energies, RMS and momentary voltage and current values for each phase, supports Rogowski coil, current transformer, Shunt or Hall current sensors, exclusive ripple-free energy calculation algorithm, programmable pulsed output, stepper motor outputs, neutral current, temperature, and magnetic field monitoring, OTP memory for configuration and calibration, SPI interface, supports IEC 62052-11 / 62053-21 / 62053-23 standards, less than 0.1 % error over 1:1000 dynamic range
ST STPMS1 handbook
STPMS1 is a smart sensor device produced by ST company. It is used in power metering, motor control, industrial process control, weight scale and pressure transducers.
ST STPMS2 handbook
STPMS2 Smart sensor II is a dual-channel 1-bit, 4 MHz, second-order sigma-delta modulator with embedded PGLNA.
ST ST802RT1A ST802RT1B handbook
ST802RT1A ST802RT1B 10/100 real-time Ethernet 3.3 V transceiver is a high-performance fast Ethernet physical layer interface for 10Base-T, 100Base-TX and 100Base-FX applications.
ST ST8024L handbook
This document provides information on the ST8024L smartcard interface product, which is designed to be compatible with the NDS conditional access system, and is ISO 7816, GSM11.11, and EMV 4.2 compatible. It features an IC card interface, can be powered by 3V or 5V, and has three specifically protected half-duplex bi-directional buffered I/O lines, among other capabilities.
ST STPM10 handbook
STPM10 is a programmable single-phase energy metering IC with tamper detection features. It can measure active, reactive, and apparent energies, current, voltage RMS, and instantaneous measurement, frequency measurement, etc. It has a ripple-free active energy pulsed output and live and neutral monitoring for tamper detection. It supports fast and simple one-point digital calibration over the whole current range. It has integrated linear voltage regulators for digital and analog supply. It supports 50 - 60 Hz - IEC62052-11, IEC62053-2x specifications. The error is less than 0.1% in the 1000:1 range. It has a precision voltage reference of 1.23 V with a maximum temperature coefficient of 30 ppm/°C.
ST L6391 handbook
The L6391 is a high-voltage high and low side driver from ST. It supports up to 600V input voltage and has overcurrent, overtemperature protection functions. It is suitable for home appliances, industrial drives, fans, etc.
ST L6398 handbook
ST TD352 handbook
The TD352 is ST's latest generation of IGBT/MOSFET gate driver, with 1.7A sink current and 1.3A source current. It features active Miller clamp function, desaturation detection, adjustable turn-on delay, UVLO protection and 2kV ESD protection. It is suitable for 1200V three-phase inverters, motor control systems and UPS applications.
ST ST8024 handbook
ST8024 is a smartcard interface of STMicroelectronics, which supports ISO 7816, GSM11.11 and EMV (payment systems) standards and is compatible with NDS conditional access systems.