STMicroelectronics manuals, page 159
ST VN808-E handbook
The VN808-E is an octal channel high side driver with VCC/2 compatible input, junction overtemperature protection, thermal independent case overtemperature protection, current limitation, shorted load protection, undervoltage shut-down, protection against loss of ground, very low standby current and compliance to 61000-4-4 IEC test up to 4 kV.
ST VN808CM-E handbook
The VN808CM-E is an eight-channel high side driver. It is designed in STMicroelectronics VIPower M0-3 technology and is intended for driving any type of load with one side connected to ground. It can be driven using a 3.3V logic supply. Active current limiting combined with thermal shutdown and automatic restart protects the device against overload. In overload condition, channel turns OFF and back ON automatically so as to maintain junction temperature between TTSD and TR. If this condition makes case temperature reach TCSD, overloaded channel is turned OFF and will restart only when case temperature has decreased down to TCR(see waveform 3 Figure 6 on page 10). Non overloaded channels continue to operate normally. Device automatically turns OFF in case of ground pin disconnection. This device is especially suitable for industrial applications conform to IEC 61131.
ST VN330SP-32-E handbook
This document describes the features and characteristics of the VN330SP-32-E quad high side smart power solid state relay, including output current, digital input voltage, shorted load and overtemperature protections, built-in current limiter, undervoltage shut-down, etc.
ST VN340SP-E handbook
This document is the datasheet of VN340SP-E, which mainly introduces the features and characteristics of the product
ST VN340SP-33-E handbook
VN340SP-33-E is a quad high side smart power solid state relay with an output current of 1A per channel and various protection features. It is designed for driving four independent resistive or inductive loads.
ST VN330SP-E handbook
The VN330SP-E is a quad high side smart Power solid state relay with an output current of 0.7A per channel, a digital input clamped at 32V minimum voltage, shorted load and overtemperature protections, built-in current limiter, undervoltage shut-down, open drain diagnostic output, and fast demagnetization of inductive loads. It conforms to IEC 61131-2.
ST VN540-E VN540SP-E VN540-12-E handbook
The VN540-E, VN540SP-E, VN540-12-E are single high side smart power solid state relays with an output current of 2.8A. The digital input is clamped at 32V and it features protection against loss of ground, shorted load, and over-temperature.
ST STOTG04E handbook
The STOTG04 is a USB On-The-Go full-speed transceiver. It provides complete physical layer (PHY) solution for any USB-OTG device. It contains VBUS charge pump and comparators, ID line detector and interrupt generator, and the USB differential driver and receivers. The STOTG04 transceiver is suitable for mobile and battery powered devices because of its low power consumption and power-down operating mode. The transceiver is capable of operation in several different modes. It can operate simultaneously in USB, I2C, UART and Audio modes.
ST STOTG04ES handbook
The STOTG04ES is a USB On-The-Go full-speed transceiver from Cypress. It supports USB, UART and audio in three operating modes, and can be configured for either 3.3V or 5V power supply. The transceiver has a typical VBUS charge pump output current of 35mA, and can control an external charge pump to achieve higher VBUS currents.
ST VN751PT handbook
The VN751PT is a high side driver with CMOS compatible input, featuring thermal shutdown, shorted load protection, undervoltage and overvoltage shutdown, protection against loss of ground, very low standby current, and compliance to the IEC 61131-2 programmable controllers international standard. It is suitable for industrial applications.
ST TDE3247 handbook
TDE3247 is a monolithic amplifier designed for high current and high voltage applications, specifically to drive lamps, relays and stepping motors. The device features high output current, adjustable short-circuit protection, internal thermal protection, and a wide supply voltage range.
ST VN751S handbook
The VN751S is a monolithic device designed in STMicroelectronics VIPower M0-3 technology, intended for driving any kind of load with one side connected to ground. Active VCC pin voltage clamp protects the device against low energy spikes. Active current limitation combined with thermal shutdown and automatic restart protect the device against overload. Device automatically turns off in case of ground pin disconnection. This device is especially suitable for industrial applications in conformity with IEC 61131-2 programmable controllers international standard.
ST VN808CM-32-E handbook
VN808CM-32-E is an octal channel high side driver with features such as CMOS compatible input, overtemperature protection, shorted load protection, etc. It is suitable for industrial applications and complies with IEC 61131 standard.
ST TDE1747 handbook
The TDE1747 is a monolithic comparator designed for high current and high voltage applications, specifically to drive lamps, relays, and stepping motors. It features open ground protection, high output current, adjustable short-circuit protection to ground, thermal protection with hysteresis to avoid intermediate output levels, and a large supply voltage range.
ST ST3222B ST3222C handbook
The ST3222 is a 3 V powered EIA/TIA-232 and V.28/V.24 communications interface with low power requirements and high data-rate capabilities. ST3222 has a proprietary low dropout transmitter output stage providing true RS-232 performance from 3 to 3.6 V power supplies. The device requires only four small 0.1 mF standard external capacitors for operating from 3 V supply. The ST3222 has two receivers and two drivers. The ST3222 features a 1 mA shutdown mode that reduces power consumption and extends battery life in portable systems. Its receivers can remain active in shutdown mode, allowing external devices such as modems to be monitored using only 1 mA supply current. The device is guaranteed to run at data rates of 250 Kbps while maintaining RS-232 output levels. Typical applications are notebooks, sub- notebooks and palmtop computers, battery powered equipment, hand-held equipment, peripherals and printers.