Maxim manuals, page 78
MAXIM MAX7031 Low-Cost 308MHz 315MHz 433.92MHz FSK Transceiver with Fractional-N PLL handbook
The MAX7031 crystal-based, fractional-N transceiver is designed to transmit and receive FSK data at factory-preset carrier frequencies of 308MHz†, 315MHz, or 433.92MHz with data rates up to 33kbps (Manchester encoded) or 66kbps (NRZ encoded). This device generates a typical output power of +10dBm into a 50Ω load, and exhibits typical sensitivity of -110dBm. The MAX7031 features separate transmit and receive pins (PAOUT and LNAIN) and provides an internal RF switch that can be used to connect the transmit and receive pins to a common antenna. The MAX7031 transmit frequency is generated by a 16-bit, fractional-N, phase-locked loop (PLL), while the receiver's local oscillator (LO) is generated by an integer-N PLL. This hybrid architecture eliminates the need for separate transmit and receive crystal reference oscillators because the fractional-N PLL is preset to be 10.7MHz above the receive LO. Retaining the fixed-N PLL for the receiver avoids the higher current-drain requirements of a fractional-N PLL and keeps the receiver current drain as low as possible. The fractional-N architecture of the MAX7031 transmit PLL allows the transmit FSK signal to be preset for exact frequency deviations, and completely eliminates the problems associated with oscillator-pulling FSK signal generation. All frequency-generation components are integrated on-chip, and only a crystal, a 10.7MHz IF filter, and a few discrete components are required to implement a complete a
MAXIM MAX2837 handbook
The MAX2837 is a direct-conversion zero-IF RF transceiver designed specifically for 2.3GHz to 2.7GHz wireless broadband systems. It integrates all circuitry required to implement the RF transceiver function, including RF-to-baseband receive path, baseband-to-RF transmit path, VCO, frequency synthesizer, crystal oscillator, and baseband/control interface. The device also includes circuits for on-chip DC offset cancellation, I/Q error, and carrier-leakage detection. Only a few external components are needed to form a complete wireless broadband RF radio solution, including an RF bandpass filter (BPF), crystal, RF switch, PA, and passive components. The MAX2837 eliminates the need for an external SAW filter by implementing on-chip monolithic filters for both the receiver and transmitter. The baseband filters and Rx/Tx signal paths are optimized to meet stringent noise figure and linearity specifications. The device supports up to 2048 FFT OFDM and implements programmable channel filters for RF channel bandwidths ranging from 1.75MHz to 28MHz. The transceiver has a fast 2µs Tx-Rx switching time, including frequency transient settling. It is available in a small 48-pin thin QFN package measuring only 6mm x 6mm x 0.8mm.
MAXIM MAX2838 handbook
The MAX2838 is a MAXIM company's direct-conversion, zero-IF, RF transceiver designed specifically for 3.3GHz to 3.9GHz wireless broadband systems.
MAXIM MAX2839 handbook
The MAX2839 is a direct conversion, zero-IF, 2GHz 802.16e MIMO mobile WiMAX system RF transceiver with >40dB isolation, which integrates all circuitry required to implement the RF transceiver function, providing RF to baseband receive path, and base- band to RF transmit path, VCO, frequency synthesizer, crystal oscillator, and baseband/control interface.
MAXIM MAX2839AS 2.3GHz to 2.7GHz MIMO Wireless Broadband RF Transceiver handbook
The MAX2839AS is a direct conversion, zero-IF, RF transceiver specifically designed for 2.3GHz to 2.7GHz 802.16e MIMO mobile WiMAX™ systems. The device incorporates one transmitter and two receivers, with > 40dB isolation between each receiver. The MAX2839AS completely integrates all circuitry required to implement the RF transceiver function, providing RF to baseband receive path, and baseband to RF transmit path, VCO, frequency synthesizer, crystal oscillator, and base-band/control interface. The device includes a fast-set- tling sigma-delta RF synthesizer with smaller than 40Hz frequency steps and a crystal oscillator that allows the use of a low-cost crystal in place of a TCXO. The trans- ceiver IC also integrates circuits for on-chip DC-offset cancellation, I/Q error, and carrier leakage detection circuits. An internal transmit to receive loopback mode allows for receiver I/Q imbalance calibration. The local oscillator I/Q quadrature phase error can be digitally corrected in approximately 0.125° steps. Only an RF bandpass filter (BPF), crystal, RF switch, PA, and a small number of passive components are needed to form a complete wireless broadband RF radio solution. The MAX2839AS completely eliminates the need for an external SAW filter by implementing on-chip program- mable monolithic filters for both the receiver and trans- mitter, for all 2GHz and 802.16e profiles and WiBro. The baseband filters along with the Rx and Tx signal paths are optimize for various profiles to achieve optimal performance.
MAXIM MAX2842 handbook
MAXIM MAX2831/MAX2832 2.4GHz to 2.5GHz 802.11g/b RF Transceivers with Integrated PA handbook
The MAX2831/MAX2832 are direct conversion, zero-IF, RF transceivers designed specifically for 2.4GHz to 2.5GHz 802.11g/b WLAN applications.
MAXIM MAX2830 handbook
MAXIM MAX2850 handbook
The MAX2850 is a single-chip, 4-channel RF transmitter IC designed for 5GHz wireless HDMI applications. It includes all circuitry required to implement the complete 4-channel MIMO RF transmitter function and crystal oscillator, providing a fully integrated transmit path, VCO, frequency synthesis, and baseband/control interface. It includes a fast-settling, sigma-delta RF fractional synthesizer with 76Hz frequency programming step size. The IC also integrates on-chip I/Q amplitude and phase-error calibration circuits. Dynamic on/off control of four external PAs is implemented with programmable precision voltages. A 4-to-1 analog mux routes external PA power-detect voltages to the RSSI pin. On-chip monolithic filters are included for transmitter I/Q baseband signal reconstruction to support both 20MHz and 40MHz RF channels. The baseband filtering and Tx signal paths are optimized to meet stringent WHDI requirements. The upconverter local oscillator is coherent among all the transmitter channels. The reverse-link control channel uses an on-chip 5GHz OFDM receiver. It shares the RF synthesizer and LO generation circuit with the MIMO transmitter.
MAXIM MAX2851 handbook
The MAX2851 is a single-chip, 5-channel RF receiver IC designed for 5GHz wireless HDMI™ applications. The IC includes all circuitry required to implement the complete 5-channel MIMO RF receiver function and crystal oscillator, providing a fully integrated receive path, VCO, frequency synthesis, and baseband/control interface.
MAXIM MAX2411A Low-Cost RF Up/Downconverter with LNA PA Driver handbook
MAX2411A is a low-cost, low-power wireless radio front-end chip for TDD communication systems.
MAXIM MAX2511 handbook
The MAX2511 is a complete, highly integrated IF transceiver for applications employing a dual-conversion architecture. Alternatively, the MAX2511 can be used as a single-conversion transceiver if the RF operating frequency ranges from 200MHz to 440MHz. In a typical application, the receiver downconverts a high IF/RF (200MHz to 440MHz) to a 10.7MHz low IF using an image-reject mixer. Functions include an image-reject downconverter with 34dB of image suppression followed by an IF buffer that can drive an off-chip IF filter; an on-chip limiting amplifier offering 90dB of monotonic received-signal-strength indication (RSSI); and a robust limiter output driver. The transmit image-reject mixer generates a clean output spectrum to minimize filter requirements. It is followed by a 40dB variable-gain amplifier that maintains IM3 levels below -35dBc. Maximum output power is 2dBm. A VCO and oscillator buffer for driving an external prescaler are also included. The MAX2511 operates from a 2.7V to 5.5V supply and includes flexible power-management control. For applications using in-phase (I) and quadrature (Q) baseband architecture for the transmitter, Maxim offers a corresponding transceiver product: the MAX2510. The MAX2510 has features similar to those of the product in this document.
MAXIM MAX2510 handbook
MAX2510 is a highly integrated IF transceiver for digital wireless applications from MAXIM company
MAXIM MAX2410 handbook
The document describes the application of MAX2410 in time-division-duplex communication systems. The product is an RF front-end device that operates in the frequency range around 1.9GHz. It includes a low-noise amplifier (LNA), a downconverter mixer, a local-oscillator (LO) buffer, an upconverter mixer, and a variable-gain power-amplifier (PA) driver. The product features low power consumption, low noise, and high gain.
MAXIM MAX9947 handbook
The MAX9947 is an AISG-compliant, fully integrated transceiver. The MAX9947 receiver offers a typical dynamic range of 20dB and integrates a bandpass filter that operates in the 2.176MHz frequency with a narrow 200kHz bandwidth. The MAX9947 transmitter integrates a bandpass filter that is compliant with the AISG spectrum emission pro- file. It can modulate OOK signals up to 115.2kbps. The output power can be varied with external resistors from +7dBm to +12dBm to compensate for loss in the external circuitry and cabling. The MAX9947 also features a direction output to facilitate the RS-485 bus arbitration in tower-mounted equipment. The MAX9947 is available in a small, 3mm x 3mm 16-pin TQFN and is rated for operation in the -40°C to +85°C temperature range.