Maxim manuals, page 79
MAXIM MAX2045/MAX2046/MAX2047 High-Gain Vector Multipliers handbook
MAX2045/MAX2046/MAX2047 low-cost, fully integrated vector multipliers alter the magnitude and phase of an RF signal.
MAXIM MAX2472/MAX2473 handbook
The MAX2472/MAX2473 are flexible, wideband, high-reverse-isolation buffer amplifiers. The MAX2472 has dual open-collector outputs capable of delivering -5dBm into 50Ω while maintaining harmonic suppression below -25dBc. The MAX2473 has a single open-collector output with a bias control pin to vary output power from -10dBm to -2dBm while maintaining harmonic suppression below -25dBc. The combination of high reverse isolation and low supply current makes the MAX2472/MAX2473 ideal for applications requiring high performance with low power. They feature high input impedance and open-col- lector outputs for maximum flexibility, enabling them to be used with a variety of oscillator topologies. Both the MAX2472 and MAX2473 operate from a single +2.7V to +5.5V supply. With VCC = +3.0V and -25dBm input power, the MAX2472 consumes 5.2mA, while the MAX2473 consumes only 2.7mA. Both devices are avail- able in a tiny 6-pin SOT23 package requiring minimal board space. Applications include Cellular and PCS Mobile Phones, Private Mobile Radios, ISM-Band Applications, IF/RF Oscillators, and General-Purpose Buffers/Amplifiers. Typical Operating Circuits appear at end of data sheet.
MAXIM MAX9987/MAX9988 handbook
MAX9987/MAX9988 is a MAXIM's RF transceiver. The device integrates a passive two-way power splitter with high-isolation input and output buffer amplifiers. These buffers are designed to provide the high output (+14dBm to +20dBm) necessary to drive the LO inputs of high-linearity passive mixers, while offering 40dB reverse isolation to prevent LO pulling. The MAX9987 is internally matched for the cellular/GSM bands, and the MAX9988 is matched for the DCS/PCS/UMTS bands. The typical application circuit provides a nominal +17dBm output power with ±1dB variation over supply, temperature, and input power. With two optional resis- tors, the output power can be precision set from +14dBm to +20dBm. The devices offer more than 30dB output-to-output port isolation, and are offered in 5mm ✕ 5mm 20-pin thin QFN packages with exposed paddle.
MAXIM MAX9989/MAX9990 handbook
The MAX9989/MAX9990 are MAXIM’s high output LO buffers that provide +14dBm to +20dBm of output power to drive the LO inputs of high-linearity passive mixers while offering 40dB reverse isolation to prevent LO pulling. The MAX9989 is internally matched for the cellular/GSM bands, and the MAX9990 is matched for the DCS/PCS/UMTS bands. The typical application circuit provides a nominal +17dBm output power with ±1dB variation over supply, temperature, and input power. With two optional resistors, the output power can be precision set from +14dBm to +20dBm. The devices offer more than 35dB main driver output to PLL amp output isolation. Each device is offered in a 5mm x 5mm 20-pin thin QFN package with exposed paddle. Applications include cellular/GSM/DCS/PCS/UMTS base station Tx/Rx LO drives, coherent receivers, ISM wireless LAN, wireless local loop, local multipoint distribution service, and point-to-point systems.
MAXIM MAX2470/MAX2471 handbook
The MAX2470/MAX2471 are flexible, low-cost, high- reverse-isolation buffer amplifiers for applications with discrete and module-based VCO designs. Both feature differential 50Ω outputs for driving a single differential (balanced) load or two separate single-ended (unbalanced) 50Ω loads. The MAX2470 offers a single-ended input and has two selectable frequency ranges of operation: 10MHz to 500MHz and 10MHz to 200MHz. The MAX2471 offers a differential input and operates from 10MHz to 500MHz. The MAX2470/MAX2471 also feature high input impedance for maximum flexibility, enabling them to be used with a variety of oscillator topologies. High reverse isolation combined with low supply current make them ideal for applications requiring high performance with low power. These devices are also ideal for use as active baluns. The MAX2470 converts a single-ended input to a differential output. The MAX2471 is useful as a differential buffer stage or to convert from a differential input to two single-ended outputs. The MAX2470 operates from a single +2.7V to +5.5V supply. At -5dBm output power, it consumes 5.5mA in the high-frequency range and only 3.6mA in the low-frequency range. The MAX2471 operates from a +2.7V to +5.5V single supply and consumes 5.5mA. Both devices are available in ultra-small SOT23-6 plastic packages.
MAXIM MAX2620 handbook
The MAX2620 is an RF integrated circuit that combines a low-noise oscillator with two output buffers. It features low-phase noise, low power consumption, and wide supply voltage range.
MAXIM MAX2622/MAX2623/MAX2624 handbook
the max2622/max2623/max2624 are self-contained voltage-controlled oscillators (vc oscillators) that combine an integrated oscillator and output buffer in a miniature 8-pin µmax package.
MAXIM MAX2605 MAX2609 45MHz to 650MHz Integrated IF VCOs with Differential Output handbook
The MAX2605–MAX2609 are compact, high-performance intermediate-frequency (IF) voltage-controlled oscillators (VCOs) designed specifically for demanding portable wireless communication systems. They combine monolithic construction with low-noise, low-power operation in a tiny 6-pin SOT23 package. These low-noise VCOs feature an on-chip varactor and feedback capacitors that eliminate the need for external tuning elements, making the MAX2605–MAX2609 ideal for portable systems. Only an external inductor is required to set the oscillation frequency. In addition, an integrated differential output buffer is provided for driving a mixer or prescaler. The buffer output is capable of supplying up to -8dBm (differential) with a simple power match. It also provides isolation from load impedance variations. The MAX2605–MAX2609 operate from a single +2.7V to +5.5V supply and offer low current consumption. These IF oscillators can cover the 45MHz to 650MHz frequency range.
MAXIM MAX2750/MAX2751/MAX2752 handbook
the max2750/max2751/max2752 are self-contained voltage-controlled oscillators (VCOs) intended for use in the 2.4ghz to 2.5ghz ISM band
MAXIM MAX2754 1.2GHz VCO with Linear Modulation Input handbook
MAX2754 is a self-contained, linear modulation, voltage-controlled oscillator (VCO) intended for use in the 2.4GHz to 2.5GHz ISM band, particularly for FSK modulation systems that utilize a direct frequency-modulation transmit architecture. In addition to the standard frequency tuning input, this device features a linear modulation input. The frequency tuning range of 1145MHz to 1250MHz (1/2 LO) also supports an IF up to 110MHz with low side LO. The VCO is based on Maxim's proprietary monolithic VCO technology, where all VCO components are integrated on-chip, including the varactor and inductor. The MAX2754 linear modulation input offers a means to directly FM modulate the VCO with a constant modulation sensitivity over the tuning voltage input range. Typical frequency deviation is -500kHz/V which is linear to ±4% over the guaranteed frequency limits. The tuning input voltage range is +0.4V to +2.4V and the oscillator frequency is factory adjusted to provide guaranteed limits. The oscillator signal is buffered by an output amplifier stage (internally matched to 50Ω) to provide higher output power and isolate the oscillator from load impedance variations. The MAX2754 operates over a +2.7V to +5.5V supply range. This device also provides a digitally controlled shutdown mode to permit implementation of sophisticated power-supply management. In shutdown, the supply current is reduced to 0.2µA. Even when active, power consumption is a modest 41mW.
MAXIM MAX2010 handbook
The MAX2010 is an adjustable RF predistorter designed to improve power amplifier (PA) adjacent-channel power rejection (ACPR) by introducing gain and phase expansion in a PA chain to compensate for the PA’s gain and phase compression.
MAXIM MAX2009 handbook
The MAX2009 adjustable RF predistorter is designed to improve power amplifier (PA) adjacent-channel power rejection (ACPR) by introducing gain and phase expan- sion in a PA chain to compensate for the PA’s gain and phase compression.
MAXIM MAX4000/MAX4001/MAX4002 handbook
The MAX4000/MAX4001/MAX4002 low-cost, low-power logarithmic amplifiers are designed to control RF power amplifiers (PA) operating in the 0.1GHz to 2.5GHz frequency range. A typical dynamic range of 45dB makes this family of log amps useful in a variety of wireless applications including cellular handset PA control, transmitter power measurement, and RSSI for terminal devices. Logarithmic amplifiers provide much wider measurement range and superior accuracy to controllers based on diode detectors. Excellent temperature stability is achieved over the full operating range of -40°C to +85°C. The choice of three different input voltage ranges eliminates the need for external attenuators, thus simplifying PA control-loop design. The logarithmic amplifier is a voltage-measuring device with a typical signal range of -58dBV to -13dBV for the MAX4000, -48dBV to -3dBV for the MAX4001, and -43dBV to +2dBV for the MAX4002. The input signal for the MAX4000 is internally AC-coupled using an on-chip 5pF capacitor in series with a 2kΩ input resistance. This highpass coupling, with a corner at 16MHz, sets the lowest operating frequency and allows the input signal source to be DC grounded. The MAX4001/MAX4002 require an external coupling capacitor in series with the RF input port. These PA controllers feature a power-on delay when coming out of shutdown, holding OUT low for approximately 5µs to ensure glitch-free controller output. The MAX4000/MAX4001/MAX4002 fami
MAXIM MAX2205 MAX2208 handbook
MAX2205/MAX2206/MAX2207/MAX2208 are wideband power detectors from Maxim that are ideal for GSM/EDGE, TDMA and CDMA applications. These devices feature an internal RF filter that allows for average power detection of CDMA signals over a 25dB dynamic range. MAX2205/MAX2206/MAX2207/MAX2208 are available in a space-saving 2×2 UCSP package and require only three external components for system design.
MAXIM MAX4003 100MHz to 2500MHz 45dB RF Detector in a UCSP handbook
The MAX4003 is a low-cost, low-power logarithmic amplifier designed to detect the power levels of RF power amplifiers (PAs) operating from 100MHz to 2500MHz. A typical dynamic range of 45dB makes this logarithmic amplifier useful in a variety of wireless applications including cellular handset PA control, TSSI for wireless terminal devices, and other transmitter power measurements. This logarithmic amplifier provides much wider measurement range and superior accuracy than typical diode-based detectors. Excellent temperature stability is achieved over the full operating range of -40°C to +85°C. The MAX4003 logarithmic amplifier is a voltage-measuring device with a typical signal range of -58dBV to -13dBV. The input signal is internally AC-coupled by an on-chip 5pF capacitor in series with a 2kΩ resistor. This highpass coupling, with a corner at 16MHz, sets the lowest operating frequency and allows the input signal source to be DC grounded. The MAX4003 also features a power-on delay, which holds the detector output (OUT) low for approximately 5µs to ensure glitchless controller output. The MAX4003 is available in an 8-bump chip-scale package (UCSP™), an 8-pin µMAX package, and an 8-pin thin QFN package. The device consumes 5.9mA with a 3.0V supply and only 13µA when the device is in shutdown. Applications include cellular handsets (TDMA, CDMA, GPRS, GSM), TSSI for wireless terminal devices, transmitter power measurement and control, and RSSI for fiber modules.