MAXIM Manuals

The MAX6581 is a precision multichannel temperature sensor that monitors its own temperature and the temperatures of up to seven external diode-connected transistors. All temperature channels have programmable alert and overtemperature thresholds. The MAX6581 features high accuracy, low power consumption, and a flexible interface.

The MAX6694 precision multichannel temperature sensor monitors its own temperature and the temperatures of up to four external diode-connected transistors. All temperature channels have programmable alert thresholds. Channels 1 and 4 also have programmable overtemperature thresholds. When the measured temperature of a channel exceeds the respective threshold, a status bit is set in one of the status registers. Two open-drain outputs, OVERT and ALERT, assert corresponding to these bits in the status register. The 2-wire serial interface supports the standard system management bus (SMBus™) protocols: write byte, read byte, send byte, and receive byte for reading the temperature data and programming the alarm thresholds. The MAX6694 is specified for a -40°C to +125°C operating temperature range and is available in 16-pin TSSOP and 5mm x 5mm thin QFN packages.

The MAX6693 is a precision 7-channel temperature monitor with beta compensation, local temperature sensor, and 1.5°C remote temperature accuracy (+60°C to +100°C). Monitoring begins at POR for fail-safe system protection. The device also features ALERT and OVERT outputs, STBY input, and small, 20-pin TSSOP package.

This product is a digital thermometer with a measurement range of -40°C to +85°C and a selectable resolution of 9 to 12 bits. The 1-Wire interface requires one port pin for communication. Each device has a unique 64-bit factory-lasered registration number

The MAX6604 is a high-precision temperature sensor designed by Texas Instruments for thermal monitoring functions in DDR memory modules. The device is readable and programmable through the 2-wire SMBus/I2C-compatible interface. Three address inputs set the bus address for the temperature sensor to provide up to eight devices on one bus. The internal thermal sensor continuously monitors the temperature and updates the temperature data eight times per second. The master can read the temperature data at any time. Since the thermal sensor is located on the memory module, temperature data recorded accurately represents the temperature of the components on the module. Consequently, the MAX6604 provides a much more accurate measurement of module temperature than techniques involving temperature sensors on the motherboard. In addition, the device responds more quickly to temperature changes on the module than a motherboard sensor. The MAX6604 also features an interrupt-output indicator for temperature-threshold monitoring. The threshold levels are programmable through the digital interface. The MAX6604 operates from -20°C to +125°C, and is available in JEDEC-standard 8-pin TSSOP and 8-pin TDFN (2mm x 3mm) packages.

The MAX6672/MAX6673 are low-current single-wire output temperature sensors

The MAX6666/MAX6667 are high-accuracy, low-cost, low-power temperature sensors with a single-wire output. The MAX6666/MAX6667 convert the ambient temperature into a ratiometric PWM output with temperature information contained in the duty cycle of the output square wave. The MAX6666 has a push-pull output and the MAX6667 has an open-drain output. The MAX6666/MAX6667 operate at supply voltages from +3V to +5.5V. The typical unloaded supply current at 5.0V is 200µA. Both devices feature a single-wire output that minimizes the number of pins necessary to interface with a microprocessor (µP). The output is a square wave with a nominal frequency of 35Hz (±20%) at +25°C. The output format is decoded as follows: Temperature (°C) = 235 - (400 x t1) / t2 where t1 is fixed with a typical value of 10ms and t2 is modulated by the temperature (Figure 1). The MAX6666/ MAX6667 operate from -40°C to +125°C and are available in space-saving SOT23 packages.

The MAX98309/MAX98310 are mono 1.4W class AB audio amplifiers with low quiescent current, excellent SNR, and low 0.008% THD+N. They feature excellent 90dB PSRR and state of the art click-and-pop suppression.

The MAX9716/MAX9717 audio power amplifiers are ideal for portable audio devices with internal speakers. A bridge-tied load (BTL) architecture minimizes external component count, while providing high-quality audio reproduction. Both devices deliver 1.4W continuous power into a 4Ω load with less than 1% Total Harmonic Distortion (THD) while operating from a single +5V sup- ply. With an 8Ω load, both devices deliver 1W continuous power. These devices also deliver 350mW continuous power into an 8Ω load while operating from a single +3.0V supply. The devices are available as adjustable gain amplifiers (MAX9716/MAX9717A) or with internally fixed gains of 6dB, 9dB, and 12dB (MAX9717B/ MAX9717C/MAX9717D), reducing component count. A low-power shutdown mode disables the bias generator and amplifiers, reducing quiescent current consumption to less than 10nA. These devices feature Maxim’s industry-leading, comprehensive click-and-pop sup- pression that reduces audible clicks and pops during startup and shutdown. The MAX9717 features a headphone sense input (BTL/SE) that senses when a headphone is connected to the device, disables the BTL slave driver, muting the speaker while driving the headphone as a single-ended load. The MAX9716 is pin compatible with the LM4890 and is available in 9-bump UCSP™, 8-pin TDFN (3mm x 3mm), and 8-pin µMAX® packages. The MAX9717 is available in 9-bump UCSP, 8-pin TDFN, and 8-pin µMAX packages. Both devices operate over the -40°C to +85°C

The MAX9718/MAX9719 differential input audio power amplifiers are ideal for portable audio devices with internal speakers. The differential input structure improves noise rejection and provides common-mode rejection. A bridge-tied load (BTL) architecture minimizes external component count, while providing high-quality, power audio amplification. The MAX9718 is a single-channel amplifier while the MAX9719 is a dual-channel amplifier for stereo systems. Both devices deliver 1.4W continuous average power per channel to a 4Ω load with less than 1% THD+N while operating from a single +5V supply. The devices are available as adjustable gain amplifiers or with internally fixed gains of 0dB, 3dB, and 6dB to reduce component count. A shutdown input disables the bias generator and amplifiers and reduces quiescent current consumption to less than 100nA. The MAX9718 shutdown input can be set as active high or active low. These devices feature Maxim’s comprehensive click-and-pop suppression circuitry that reduces audible clicks and pops during startup and shutdown. The MAX9718 is pin compatible with the LM4895, and is available in 9-bump UCSP™, 10-pin TDFN, and 10-pin μMAX® packages. The MAX9719 is available in 16-pin TQFN, 16-pin TSSOP, and 16-bump UCSP packages. Both devices operate over the -40°C to +85°C extended temperature range.

MAX9710/MAX9711 3W Mono/Stereo BTL Audio Power Amplifiers with Shutdown

The MAX98314 mono 3.2W Class D amplifier provides Class AB audio performance with Class D efficiency.