Intersil manuals, page 15
intersil HSP9501 Data Sheet
The HSP9501 is a 10-bit wide programmable data buffer designed for use in high speed digital systems. It has two operating modes, delay mode and recirculate mode. In delay mode, it can provide 2 to 1281 clock cycles of delay. In recirculate mode, it provides a programmable circular buffer. The length of the buffer or amount of delay can be programmed through the LC0-10 length control input port and the LCEN length control enable port.
intersil HRP2540 handbook
The HRP2540 is a high forward current, high reverse energy controlled avalanche power rectifier. It uses an ion-implanted planar epitaxial construction. This device was designed for use as the output rectifier in the three phase six diode bridge assembly of an automotive alternator system. It provides “Load Dump” suppression by virtue of its precisely controlled reverse avalanche breakdown voltage. When used singly it can also serve as a transient suppressor for an automotive accessory. This device can provide for- ward voltage clamping and reverse voltage bypassing. This will protect the accessory from L-C inductive spikes and/or field decay transients.
intersil HIP4020 handbook
HIP4020 is a half-bridge power switch chip released by Intersil for driving small-power DC motors. It can drive 3V, 5V and 12V DC motors.
intersil HI3256 handbook
The HI3256 is an 8-bit, high-speed, flash analog-to-digital converter optimized for high speed, low power, and ease of use. With a 120MSPS encode rate capability and full-power analog bandwidth of 250MHz, this component is ideal for applications requiring the highest possible dynamic performance.
intersil FSF055D FSF055R handbook
The document introduces a series of radiation-hardened MOSFET products developed by Intersil Corporation. These products feature resistance to Single Event Effects (SEE), particularly Single Event Gate Rupture (SEGR), making them suitable for commercial and military space applications. The products have a total dose hardness of up to 100K RADS and maintain the necessary dose rate and neutron tolerance for military applications.
intersil HUF75345G3 HUF75345P3 HUF75345S3Shandbook
This product is a 75A, 55V, 0.007 Ohm, N-Channel UltraFET Power MOSFETs produced by Intersil Corporation. It has high performance, low power consumption, low reverse recovery time and stored charge.
intersil X9420 Low Noise/Low Power/SPI Bus handbook
The X9420 is a low noise/low power/SPI Bus single digitally controlled (XDCP™) potentiometer with a SPI serial interface. The potentiometer has a register-oriented format that enables direct read/write/transfer of wiper positions and storage of as many as four positions per potentiometer. The potentiometer is powered by VCC = 2.7V to 5.5V, V+ = 2.7V to 5.5V, and V– = -2.7V to -5.5V. The potentiometer is a CMOS device with standby current of less than 1 µA. The potentiometer is highly reliable and can withstand 100,000 data changes per bit per register and register data retention of 100 years. The potentiometer has 8 bytes of nonvolatile EEPROM memory. The potentiometer's resistor arrays are 10kΩ or 2.5kΩ. The potentiometer's resolution is 64 taps per pot. The potentiometer's packages are 14Ld TSSOP and 16Ld SOIC. The potentiometer is available with lead-free and annealed finishes and is RoHS compliant.
intersil X80000 X80001 handbook
The X80000 is a smart power plug with penta-power sequence controller and hot swap function. It contains three major functions: a power communications controller, a power sequencing controller, and a hotswap controller. The power communications controller allows smart power supply control via the backplane using the SMBus protocol. The system can check for voltage, current, and manufacturing ID compliance before board insertion. The power distribution network can monitor the status of the negative voltage supply, DC voltage supplies, and hardshort events by accessing the Fault Detection Register and General Purpose EEPROM of the device. Each device has a unique slave address for identification. The power sequencer controller time sequences up to five DC-DC modules. The X80000 allows for various hardwired configurations, either parallel or relay sequencing modes. The power good, enable and voltage good signals provide for flexible DC-DC timing configurations. Each voltage enable signal has a programmable delay. In addition, the voltage good signals can be monitored remotely via the fault detection register (thru the SMBus). The hot
intersil X55060 64K handbook
X55060 is a battery monitoring chip produced by Intersil company, which has dual voltage monitoring, high and low level reset output, programmable reset threshold, low level output, system battery switching circuit, programmable watchdog timer, 64Kbits EEPROM, built-in inadvertent write protection circuit, 10MHz SPI interface and other features
intersil HIN232 HIN236 HIN237 HIN238 HIN239 HIN240 HIN241 handbook
The HIN232-HIN241 family of RS-232 transmitters/receivers interface circuits meet all EIA RS-232E and V.28 specifications, and are particularly suited for those applications where ±12V is not available. They require a single +5V power supply (except HIN239) and feature onboard charge pump voltage converters which generate +10V and -10V supplies from the 5V supply. The family of devices offer a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The drivers feature true TTL/CMOS input compatibility, slew-rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V, and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection.
intersil CD22103A Data Sheet
The CD22103A is an integrated circuit that performs HDB3 transmission coding and reception decoding functions for 2.048/8.448Mb/s transmission applications. It operates at data rates from 50Kb/s to 10Mb/s, consistent with CCITT G703 recommendations. The product includes HDB3 encoder and decoder sections with code error detection.
intersil ISL6227 handbook(1)
ISL6227 is a dual PWM controller from ISL company, which adopts synchronous buck DC/DC converter and can provide power regulation for DDR memory, chipset, graphics and other system electronics. It supports AC/DC adaptor or Li-ion battery pack and automatically switches mode under heavy load and light load to ensure high efficiency under various conditions.
intersil ISL43840 handbook
The ISL43840 is a low-voltage, single and dual supply, dual 4 to 1 multiplexer analog switch with enable function. Produced by Intersil, this product is designed to operate from a single +2V to +12V supply or from a ±2V to ±6V supply. Each switch can handle rail to rail analog signals. It features low off-leakage current and a wide range of digital input logic thresholds, making it suitable for various application scenarios.
intersil EL5120 EL5220 EL5420 Data Sheet
EL5120, EL5220, and EL5420 are low power, high voltage, rail-to-rail input-output amplifiers. They have a bandwidth of 12MHz, common mode input ability beyond the supply rails, and rail-to-rail output capability.
intersil EL5162 EL5163 EL5262 EL5263 EL5362 handbook
EL5162, EL5163, EL5262, EL5263, EL5362 500MHz Low Power Current Feedback Amplifiers