Intersil manuals, page 18
intersil EL7556D handbook
The EL7556D is an adjustable synchronous DC:DC switching regulator optimized for a 5V input and 1.0V-3.8V output. By combining integrated NMOS power FETS with a fused-lead package, the EL7556D can supply up to 6A continuous output current without the use of external power devices or discrete heat sinks, thereby minimizing design effort and overall system cost. On-chip resistorless current sensing is used to achieve stable, highly efficient, current-mode control. The EL7556D also incorporates the VCC2DET function to directly interface with the Intel P54 and P55 microprocessors. Depending on the state of VCC2DET, the output voltage is internally preset to 3.5V or a user-adjustable voltage using two external resistors. In both internal and external feedback modes the active-high PWRGD output indicates when the regulator output is within ±10% of the programmed voltage. An on- board sensor monitors die temperature (OT) for over- temperature conditions and can be connected directly to OUTEN to provide automatic thermal shutdown. Adjustable oscillator frequency and slope compensation allow added flexibility in overall system design. The EL7556D is available in a 28-pin SO package and is specified for operation over the full -40°C to +85°C temperature range.
intersil EL5224 EL5324 EL5424 handbook
EL5224, EL5324, EL5424 12MHz Rail-to-Rail Buffers + 100mA VCOM Amplifier is a series of products including 8, 10, 12 low power buffers and one 100mA high power output amplifier, which are used for buffering column driver reference voltages in TFT-LCD applications as well as generation of the VCOM supply.
intersil EL5102 EL5103 EL5202 EL5203 EL5302 datasheet
EL5102, EL5103, EL5202, EL5203, EL5302 400MHz Enhanced Voltage Feedback Amplifiers
intersil X9438 handbook
The X9438 is a monolithic CMOS IC that incorporates two operational amplifiers and two nonvolatile digitally controlled potentiometers. The amplifiers are CMOS differential input voltage operational amplifiers with near rail-to-rail outputs. The digitally controlled potentiometers consist of a series string of 63 polycrystalline resistors that behave as standard integrated circuit resistors.
intersil X5323 X5325 handbook
INTERSIL DG426/A DG429/A DG433/A DG434/A DG440/A DG441/A DG451/A DG452/A DG453/A DG454/A 2-Channel Drivers with SPST DPST FET Switches
intersil HFA3424 handbook
Intersil HFA3424 is a 2.4GHz - 2.5GHz low noise amplifier that offers increased sensitivity for systems targeting the 802.11 specifications. It features low noise figure, high gain, high dynamic range, and low power consumption, making it suitable for Wireless Local Area Network and wireless data collection markets.
intersil X9279 Single Supply/Low Power/256-Tap/2-Wire Bus handbook
The X9279 is a single supply/low power/256-tap/2-wire bus single digitally controlled potentiometer. It features 256 resistor taps and a 2-wire serial interface for write, read, and transfer operations. The device has nonvolatile storage of multiple wiper positions for each potentiometer, power-on recall, low standby current, and high data retention capability.
intersil X5643 X5645 Data Sheet
intersil X4283 X4285 handbook
The X4283/85 is a low-power CPU supervisor from Intersil that features 4 selectable watchdog timers, low voltage detection and reset assertion, and 128K bits of EEPROM. It supports 64-byte page write mode, self-timed write cycle, 5ms write cycle time (typical), and built-in inadvertent write protection. It also supports programmable Block Lock protection for 0, 1/4, 1/2, all or 64, 128, 256 or 512 bytes of the EEPROM array. It supports a 400kHz 2-wire interface and works with a power supply voltage range of 2.7V to 5.5V. It comes in 8-lead SOIC and 8-lead TSSOP packages.
intersil HCS161MS Data Sheet
The Intersil HCS161MS Radiation Hardened Synchronous Counter is a 4-input binary synchronous counter from Intersil Corporation that features asynchronous reset and look-ahead carry logic. The counter has an active-low master reset to zero MR pin, and a low level on the synchronous parallel enable (SPE) pin disables counting and allows Q0 to be shifted to Q1.
intersil JANSR2N7402 3A 500V 2.70 Ohm Rad Hard N-Channel Power MOSFET handbook
JANSR2N7402 is a 3A, 500V, 2.70 Ohm, Rad Hard, N-Channel Power MOSFET from Intersil.
intersil ACS573MS Radiation Hardened Octal Three-State Transparent Latch handbook
This file introduces the features and characteristics of the ACS573MS radiation hardened octal three-state transparent latch, including total dose, single event upset (SEU) immunity, dose rate upset, dose rate survival, latch-up free conditions, military temperature range, significant power reduction, and DC operating voltage range
intersil HIN202 HIN206 HIN207 HIN208 HIN211 HIN213 handbook
HIN202, HIN206, HIN207, HIN208, HIN211, HIN213 are a family of RS-232 transmitters/receivers interface circuits that are powered by a single +5V power supply and meet all EIA RS-232E and V.28 specifications. They are particularly suited for applications where ±12V is not available. The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The HIN206, HIN211 and HIN213 feature a low power shutdown mode to conserve energy in battery powered applications. In addition, the HIN213 provides two active receivers in shutdown mode allowing for easy “wakeup” capability. The drivers feature true TTL/CMOS input compatibility, slew rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V input, and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection. Applications • Any System Requiring RS-232 Communications Port - Computer - Portable, Mainframe, Laptop - Peripheral - Printers and Terminals - Instrumentation - Modems Features • Meets All RS-232E and V.28 Specifications • Requires Only 0.1µF or Greater External Capacitors • High Data Rate.
intersil HS-1254RH handbook
The HS-1254RH is a ±5V, Rad Hard, monolithic, dual, current feedback amplifier that provides highly reliable performance in harsh radiation environments. Dielectric isolation and bonded wafer processing make this device immune to latch-up (SEL). Excellent dynamic characteristics, coupled with the disable function, make this amplifier well-suited for a variety of satel- lite system applications. The outputs have individual disable control pins that make it easy to multiplex wideband signals, putting the outputs in a high impedance mode and reducing the supply current per op amp down to 3mA (typical). Post radiation limits are fully speci