ANALOG Manuals

The Multiformat SDTV Video Decoder ADV7189 Rev. B is a video decoder that supports multiple video input signal formats, with features such as noise reduction, adaptive digital line length tracking, and automatic format identification.

12-Bit R/D Converter with Reference Oscillator

The AD10242 is a 2-channel analog-to-digital converter from Analog Devices that features a 40 MSPS sample rate and 80 dB of spurious-free dynamic range. It is suitable for applications that require wide dynamic range, such as radar processing, communications receivers, FLIR processing, and secure communications.

This document is a data sheet for the REV. A AD5210 series, describing the features and characteristics of the products.

This document describes the ADE7759 active energy metering IC, which features high accuracy, on-chip digital integrator, and interface with current sensors with di/dt output.

AD9975 is a low-cost, 3.3 V-CMOS, mixed-signal front-end converter for broadband modems. It contains a transmit path interpolation filter and DAC, and a receive path PGA, LPF, and ADC required for a variety of broadband modems.

The AD872A is a monolithic 12-bit, 10 MSPS analog-to-digital converter with low noise, small differential nonlinearity error, high signal-to-noise and distortion ratio, and large spurious-free dynamic range.

AD9483 is a triple 8-bit monolithic analog-to-digital converter from Analog Devices. It can be used in applications such as RGB graphics processing, high resolution video, LCD monitors and projectors, micromirror projectors, plasma display panels and scan converters.

ADV7181 Rev. B is a multiformat SDTV video decoder produced by Analog Devices, which supports NTSC-(J, M, 4.43), PAL-(B/D/G/H/I/M/N), SECAM formats, integrates three 54 MHz, 9-bit ADCs, clocked from a single 27 MHz crystal, has line-locked clock-compatible (LLC), adaptive digital line length tracking (ADLLT™) and other features.

ADADC71 is a high-resolution 16-bit A/D converter from Analog Devices. It has a maximum nonlinearity of ±0.003%, no missing codes to 14 bits, fast conversion speed of 35μs (14 bits), short cycle capability, parallel logic outputs, and low power consumption of only 645mW.

The AD9876 is a single-supply broadband modem mixed-signal front end (MxFE) IC. The device contains a transmit path interpolation filter and DAC and a receive path PGA, LPF, and ADC supporting a variety of broadband modem applications. Also on-chip is a PLL clock multiplier that provides all required clocks from a single crystal or clock input. The AD9876 provides 12-bit converter performance on both the Tx and Rx path. The TxDAC+ uses a selectable digital 2× or 4× interpolation low-pass or band-pass filter to further oversample transmit data and reduce the complexity of analog reconstruction filtering.

The AD7880 is a high speed, low power, 12-bit A/D converter which operates from a single +5 V supply. It features a 3 µs track/hold amplifier, a 12 µs successive-approximation ADC, versatile interface logic, and a multiple-input-range circuit. The part also includes a power save feature. It is suitable for battery-powered portable systems, digital signal processing, speech recognition and synthesis, high-speed modems, control and instrumentation applications.

The AD6622 is a four-channel, 75 MSPS digital transmit signal processor (TSP) from Analog Devices that offers wideband digital IF parallel output, wideband digital IF parallel input, allows cascading of chips for additional channels, programmable IF and modulation, programmable interpolating RAM coefficient filter, high-speed CIC interpolating filter, NCO frequency translation, worst spur better than 100 dBc, tuning resolution better than 0.02 Hz, real or complex outputs, digital summation of channels, clipped or wrapped overrange, two’s complement or offset binary output, separate 3-wire serial data input for each channel, microprocessor control, JTAG boundary scan and other features.