Analog Devices Manuals

AD8021 is a very high performance, high speed voltage feedback amplifier that can be used in 16-bit resolution ADC preamp and driver, instrumentation preamp, active filters, portable instrumentation, line receivers, precision instruments, ultrasound signal processing and high gain circuits.

The AD8019 is a low-cost xDSL line driver optimized to deliver a minimum of 13 dBm of output power into a 100 Ω load while providing outstanding distortion performance.

The AD8018 is a 5V, rail-to-rail, high-output current xDSL line drive amplifier. It is an ideal amplifier for USB, PCMCIA, or PCI-based customer premise equipment (CPE). The AD8018 provides maximum reach on a 5V supply, driving 16 dBm of power into a back-terminated, transformer-coupled 100-ohm load while maintaining -82 dBc of out-of-band SFDR. The amplifier features rail-to-rail output voltage and high output current drive, with the ability to drive 400 mA of output current into a differential load of 10 ohms at 8V p-p. It has low single-tone distortion of -86 dBc worst harmonic at 6V p-p into a differential 10-ohm load at 100 kHz. The AD8018 also has low noise, low power operation, high speed, and current feedback amplifiers.

The AD8017 is a low cost, dual high speed amplifier capable of driving low distortion signals to within 1.0 V of the supply rail. It is intended for use in single supply xDSL systems where low distortion and low cost are essential. The amplifiers will be able to drive a 50 Ohm load with 20 V p-p differential output or a 25 Ohm load with 10 V p-p single ended output.

The AD8016 is a high output current xDSL line driver from Analog Devices. It features low power, high output current and high speed. The device supports -5V to -12V power supply, works with less than 50mA of current, and can provide up to 24.4dBm of output power for ADSL, HDSL2 and proprietary xDSL systems.

AD8015 is a wideband/differential output transimpedance amplifier launched by Analog Devices, with low cost, wide bandwidth, and low noise.

AD8014 is a high performance low power amplifier with 400MHz bandwidth, 1.15mA low power, 4000V/µs slew rate, 60ns fast recovery time, 24ns fast response time, 3.5nV/√Hz and 5pA/√Hz low noise, 5nV/√Hz total input noise, 500Ω feedback resistor, +4.5V to +12V power supply, -70dB THD low distortion, low temperature drift DC offset, SOIC-8 and SOT-23-5 package

The AD8012 is a dual low power current feedback amplifier capable of providing high output current, high speed and low distortion.

This document describes the features and characteristics of the AD8011 model, including easy to use, low power consumption, high speed and fast settling, good video specifications, low distortion, etc.

AD8010 is a low power, high current amplifier capable of delivering a minimum load drive of 175 mA. While driving eight 75 Ω back terminated video lines, signal performance such as 0.02% and 0.03° differential gain and phase error are maintained. The current feedback amplifier features gain flatness to 60 MHz and –3 dB (G = +1) signal bandwidth of 230 MHz and only requires a typical of 15.5 mA supply current from ±5 V supplies. These features make the AD8010 an ideal component for Video Distribution Amplifiers or other video applications.

The AD8009 is a high-performance, low distortion, ultrahigh speed current feedback amplifier with a phenomenal 5500 V/µs slew rate that results in a rise time of 545 ps, making it ideal as a pulse amplifier. The AD8009 has a 1 GHz bandwidth and features –40 dBc of distortion, which meets the requirements of high-resolution video graphics systems.

The AD8009 is a high performance single-channel low distortion amplifier that utilizes a phenomenal 5500 V/µs slew rate to achieve a rise time of 545 ps, making it ideal for pulse amplification applications.

The AD8007/AD8008 are high performance current feedback amplifiers with ultralow distortion and noise. Unlike other high performance amplifiers, the low price and low quiescent current allow these amplifiers to be used in a wide range of applications. ADI's second generation eXtra-Fast Complementary Bipolar (XFCB) process enables such high performance amplifiers with low power consumption. The AD8007/AD8008 have 650 MHz bandwidth, 2.7 nV/√Hz voltage noise, -83 dB SFDR @ 20 MHz (AD8007), and -77 dBc SFDR @ 20 MHz (AD8008). With the wide supply voltage range (5 V to 12 V) and wide bandwidth, the AD8007/AD8008 are designed to work in a variety of applications. The AD8007/AD8008 amplifiers have a low power supply current of 9 mA/amplifier. The AD8007 is available in a tiny SC70 package as well as a standard 8-lead SOIC. The dual AD8008 is available in a compact 8-lead SOIC package.

The document provides information about AD8005 from Analog Devices. AD8005 is an ultralow power, high-speed amplifier suitable for signal conditioning, A/D buffering, power-sensitive high-speed systems, battery-powered equipment, loop/remote power systems, communication or video test systems, and portable medical instruments. It features low power consumption, high speed, low distortion/noise, and good video specifications.