ANALOG Manuals

This document introduces the features and characteristics of the 8-bit high-speed multiplying D/A converter DAC08.

ADE7762 is a polyphase energy metering IC with phase drop indication. It supports high accuracy metering at 50Hz/60Hz with less than 0.1% error over a dynamic range of 500:1. The IC is compatible with 3-phase, 3-wire delta and 3-phase, 4-wire Wye configurations and provides average active power outputs and high frequency outputs for calibration. It also features phase sequence error detection, dropout indication for each phase, and on-chip power supply monitoring.

The AD8335 is a low-noise, low-cost quad variable gain amplifier that can be used in medical imaging, sonar, and test and measurement applications. It features a low-noise preamplifier, differential output, and wideband gain control.

VisualDSP++ is an integrated development environment for Analog Devices' Blackfin, SHARC, and TigerSHARC processors. It supports C/C++ programming and includes a rich library of signal processing routines to accelerate development

ADV3205 is a 16 × 16 high speed nonblocking switch array, which has serial or parallel programming of switch array, serial data out allows daisy-chaining control of multiple 16 × 16 devices to create larger switch arrays, complete solution, buffered inputs, 16 output amplifiers, operates on ±5 V supplies, supply current of 50 mA, excellent video performance, VS = ±5 V -3 dB bandwidth: 60 MHz 0.1 dB gain flatness: 10 MHz 0.1% differential gain error (RL = 1 kΩ) 0.1° differential phase error (RL = 1 kΩ) low all hostile crosstalk: −67 dB at 5 MHz output disable allows connection of multiple devices without loading the output bus RESET pin allows disabling of all outputs power-on reset capability with capacitor to ground 100-lead LQFP (14 mm × 14 mm) applications: CCTV surveillance, industrial automation, security, automotive, medical equipment, etc.

ADV3224/ADV3225 is an 16 x 8 analog crosspoint switch produced by Analog Devices. It has the characteristics of high speed, non-blocking switch array, programmable high impedance output, etc., and is applied to fields such as video, compressed video, and three-level digital video.

This document describes the features and characteristics of the 750 MHz, 8 × 8 analog crosspoint switch ADV3228/ADV3229. The switch is high speed and nonblocking, with a 16 × 8 array. It has buffered inputs and programmable high impedance outputs. Additionally, the switch has low power consumption and excellent AC performance.

ADV3226/ADV3227 is a 16×16 high performance switch array, which is pin compatible with AD8114/AD8115, providing a complete solution with buffered inputs and programmable high impedance outputs. It can drive 150Ω loads, operate on ±5V supplies, with low power consumption of 1.3W.

ADV3200/ADV3201 32 × 32 Buffered Analog Crosspoint Switch is a switch array chip produced by Analog Devices, supporting single 5V, dual ±2.5V, dual ±3.3V power supply, with 60MHz, 0.1dB gain flatness, 0.1% differential gain error (RL = 150 Ω), 0.1° differential phase error (RL = 150 Ω), >300MHz bandwidth, >400V/μs slew rate, 1.25W power consumption, and -48dB @ 5MHz suppression ratio

The ADV3202/ADV3203 are 300MHz, 32×16 buffered analog crosspoint switches

AD8104/AD8105 is a 32x16 high speed non-blocking switch array from Analog Devices, which supports differential or single-ended operation, supports single +5V power supply or dual ±2.5V power supply, and can be programmed in serial or parallel. It has excellent video performance and ac performance, and its power consumption is only 1.7W.

The AD8176 is a 450 MHz triple 16×9 video crosspoint switch. It features a large, high-speed, non-blocking switch array that is pin compatible with the AD8175 (16×9 switch array) and AD8177, AD8178 (16×5 switch arrays). It supports differential or single-ended operation and sync-on common-mode and sync-on color operating modes. It also offers RGB and HV outputs for driving a monitor directly. The AD8176 operates at G = +4 (differential input to differential output) and has flexible power supply options of +5 V or ±2.5 V. It can be controlled via a convenient interface with logic ground and supports serial or parallel programming of the switch array. The AD8176 also has an adjustable output CM and black level through external pins and offers excellent AC performance with a bandwidth of 450 MHz, a slew rate of 1650 V/μs, and a settling time of 4 ns to 1% to support 1600×1200 resolution.

AD8178 is a high performance video crosspoint switch from Analog Devices. It has a 16x5 array, supports differential or single-ended input, supports 450MHz bandwidth, 1650V/μs slew rate and 4ns settling time.

The document introduces the AD8117/AD8118 model of a 32×32 buffered analog crosspoint switch, which features a high channel count, differential or single-ended operation, flexible power supplies, and serial or parallel programming. In addition, the product offers excellent video performance, outstanding AC performance, and low power consumption.

AD8175 is a high channel count, triple 16 × 9 high-speed crosspoint switch array that supports differential or single-ended operation and is suitable for sync-on common-mode and sync-on color operating modes.