ATMEL Manuals (Industrial)

This document provides a cross-reference table of Farnell and Equinox order codes, as well as a product selection guide for the Atmel AVR microcontroller family. The document lists the features and characteristics of different models of microcontrollers, including storage capacity, programmability, and hardware features.

File format: PDF Size:680 KB

This document introduces the features and characteristics of the ATmega162 microcontroller, including high performance, low power, high endurance non-volatile memory segments, JTAG (IEEE std. 1149.1 Compliant) interface, boundary scan capabilities, extensive on-chip debug support, two 8-bit timers/counters, one 16-bit timer/counter, real time counter, four PWM channels, 8-channel, 10-bit ADC 8 single-ended channels 7 differential channels in TQFP package only 2 differential channels with programmable gain(1x, 10x or 200x), byte-oriented two-wire serial interface, programmable serial USART, master/slave SPI serial interface, programmable watchdog timer

File format: PDF Size:495 KB

JTAGICE mkII is Atmel's on-chip debugging tool for the AVR® microcontroller family. It supports debugging with AVR's traditional JTAG interface and with the debugWIRE interface. The JTAGICE mkII supports PC communication via RS-232 and USB. It is supported by AVR Studio version 4.09 and later. When connecting to the target board through the debugWIRE interface, only the RESET pin is used for communication. To enable the debugWIRE interface on an AVR Device, the debugWIRE Enable fuse, DWEN, must be programmed (DWEN=0). AVR devices with debugWIRE interface are shipped with the DWEN fuse unprogrammed. ISP or High-Voltage Programming is required to enable debugWIRE. Programming the fuse via ISP requires an ISP header on the target board. Using the 6-pin ISP header as shown in Figure 1 is recommended. The JTAGICE mkII supports ISP as a general programming interface, as well as having built-in support for handling the DWEN fuse and performing the Chip Erase when debugging. ISP is also supported by Atmel's STK500 and AVRISP mkII. See the relevant user guides for more information. All user guides are found in the AVR Studio Online help. The recommended connection when the JTAGICE mkII is used for both debugWIRE and limited ISP is the ISP6PIN header. See Figure 1, Figure 2 on page 2, and Table 1 on page 2.

File format: PDF Size:216 KB

This document discusses the advantages of Atmel's megaAVR family of microcontrollers in terms of reducing time-to-market and improving production efficiency. It describes the development tools, on-chip resources, efficiency for high level languages, and fast and reliable programming capabilities of this microcontroller family.

File format: PDF Size:346 KB

AT88SC018 is a CryptoCompanion™ chip for CryptoMemory® and CryptoRF®. It securely implements host algorithms, securely stores host secrets, and verifies host firmware digests.

File format: PDF Size:325 KB

This document describes a product with multiple features, including user memories from 1-Kbit to 8-Kbits, 1-Kbit EEPROM user memory, 2-Kbit configuration zone, high security features, smart card features, embedded application features, and high reliability features.

File format: PDF Size:716 KB

This document provides detailed information on the AT24C32A, a 2KB EEPROM manufactured by Microchip. It features multiple security features, including a 64-bit mutual authentication protocol, cryptographic message authentication codes, and stream encryption. It also supports ISO 7816 Class B (3V) operation and ISO 7816-3 Asynchronous T=0 protocol. In addition, it has low voltage supply, secure nonvolatile storage, and 2-wire serial interface.

File format: PDF Size:717 KB

This datasheet introduces the features and characteristics of AT24C404 series EEPROM, including product features, high security features, smart card features, embedded application features and high reliability.

File format: PDF Size:739 KB

The document describes a smart card product with multiple features and functionalities, including 8-Kbit EEPROM user memory, 2-Kbit configuration zone, high security features, smart card functionalities, and embedded application features.

File format: PDF Size:759 KB

The product is STMicroelectronics' ST95F8063R, a 1Kbit EEPROM with self-timed write cycle, single byte or 16-byte page write mode, programmable access rights, 37-byte OTP area and 160-byte area. In addition, the product also has high security features, including a 64-bit mutual authentication protocol, encrypted checksum, stream encryption, four key sets for authentication and encryption, eight sets of two 24-bit passwords, anti-tearing function and voltage and frequency monitor. In addition, the product also has smart card features, embedded application features and high reliability features.

File format: PDF Size:559 KB

2-Kbit EEPROM series products are a family of high security and embedded application smart card products.

File format: PDF Size:544 KB

The document introduces the AT24CS04-R series EEPROM products, including 4-Kbit (512-byte) EEPROM User Memory, 2-Kbit Configuration Zone, High Security Features, Smart Card Features, Embedded Application Features, High Reliability etc.

File format: PDF Size:544 KB

The document describes the features and characteristics of a smart card product. The smart card has high security features, including a 64-bit mutual authentication protocol, encrypted checksum, and stream encryption. It also has multiple user memory zones and key sets, as well as low voltage operation from 2.7V to 5.5V. Additionally, the smart card features ISO 7816 Class A or Class B operation, ISO 7816-3 asynchronous T = 0 protocol (Gemplus Patent), and ISO 7816-2 compliant modules.

File format: PDF Size:546 KB

This document introduces the characteristics of ST9550 16Kbit EEPROM, including 16Kbit user memory, 2Kbit configuration zone, high security features, smart card features, embedded application features, and high reliability features.

File format: PDF Size:549 KB

This document describes the features and characteristics of a smart card product, including user memory, configuration zone, high security features, smart card functions, and embedded application features.

File format: PDF Size:502 KB

The product is a 64-Kbit (8-Kbyte) EEPROM User Memory with 16 512-byte (4-Kbit) Zones, self-timed write cycle, single byte or 128-byte page write mode, and programmable access rights for each zone. It also has a 2-Kbit Configuration Zone, 37-byte OTP Area, 160-byte Area for User-defined Keys and Passwords, high security features, smart card features, embedded application features, and high reliability features.

File format: PDF Size:522 KB

This datasheet introduces the 8-Kbyte 128-Kbit EEPROM, including features, security features, smart card features, embedded application features, high reliability, etc.

File format: PDF Size:501 KB

AT88SC0104CRF to AT88SC6416CRF is a family of contactless secure memory devices with advanced security and cryptography.

File format: PDF Size:1172 KB

The new CryptoMemory family of devices in plastic packages provides secure serial EEPROM storage for sensitive information within an embedded system.

File format: PDF Size:702 KB

The AT24C128/256 are a series of serial electrically erasable and programmable read only memory (EEPROM) for automotive applications, providing 131,072/262,144 bits, organized as 16,384/32,768 words of 8 bits each. The device's cascadable feature allows up to 4 devices to share a common Two-wire bus. The device is optimized for use in many automotive applications where low power and low voltage operation are essential. The AT24C128 is available in space-saving 8-lead JEDEC SOIC and 8-lead TSSOP packages. The AT24C256 is available in a space-saving 8-lead JEDEC SOIC package. In addition, the entire family is available in 2.7V (2.7V to 5.5V) version.

File format: PDF Size:246 KB